Pages: « 1 2 3 4 5 6 7 8 9 10 »   Go Down

Author Topic: SPIKE'S BURTHA CELL  (Read 37547 times)

0 Members and 2 Guests are viewing this topic.

Offline Login to see usernames

  • Member
  • **
  • Posts: 267
  • OO-Rah!
Re: SPIKE'S BURTHA CELL
« Reply #64 on: July 20, 2008, 17:40:24 pm »
waterfalcon

I have hooked my karebill 12 up in parallel, And yes, It did pull more amps. But It produced the most in its current hookup.\

Spike
Logged

Offline Login to see usernames

  • Member
  • **
  • Posts: 267
  • OO-Rah!
Re: SPIKE'S BURTHA CELL
« Reply #65 on: August 02, 2008, 03:15:10 am »
 :'( Blown Cell  :'(

Today, I was trying a new torch out. And getting good results. (10" flame!!!)
Then I heard a Low grunting pop, Turning to see the top of my cell falling
back down on top of  the remains of my cell. And water falling to the floor.

Hard lessons learned

1- If you are going to restrict flow, Get a PSI gauge.
2- Install a high pressure shutoff or pop off

Spike
Logged

Offline Login to see usernames

  • 50+
  • *
  • Posts: 93
Re: SPIKE'S BURTHA CELL
« Reply #66 on: August 02, 2008, 03:37:02 am »

 Ouch.  Repairable ???
Logged

Offline Login to see usernames

  • Member
  • **
  • Posts: 267
  • OO-Rah!
Re: SPIKE'S BURTHA CELL
« Reply #67 on: August 02, 2008, 04:04:05 am »
 ;D Very Repairable  ;D

Just time consuming, And a little bit of redesign.  ;)

Spike
Logged

Offline Login to see usernames

  • Pochin Hydrogen
  • Jr. member
  • *
  • Posts: 32
  • Hydrogen to Drive
    • PochinTwin Hydrogen
Re: SPIKE'S BURTHA CELL
« Reply #68 on: August 03, 2008, 02:00:23 am »
nice work sripke ;)
Logged

Offline Login to see usernames

  • Member
  • **
  • Posts: 267
  • OO-Rah!
Re: SPIKE'S BURTHA CELL
« Reply #69 on: August 03, 2008, 03:17:53 am »
pochintwin

 :'( All I can do now is learn from it   :'(

Spike
Logged

h2opower

  • Guest
Re: SPIKE'S BURTHA CELL
« Reply #70 on: August 03, 2008, 08:47:15 am »
Sorry to hear the bad news Spike, I loved that cell :D. If you say it is repairable thank heavens, and you might what to try and get some access to the center electrod so you can try out lots of different wirings on it.

Sure wish you the best of luck on your repairs
br,
h2opower.
Logged

Offline Login to see usernames

  • Jr. member
  • *
  • Posts: 41
Re: SPIKE'S BURTHA CELL
« Reply #71 on: August 03, 2008, 13:18:00 pm »
Spike,
  Just an idea, but when you glue your end cap back on, maybe install some roll pins or dowels through the cap into your manifold plate.  This would probably reduce some the stress.

Just a thought.

LapperL
Logged
Pages: « 1 2 3 4 5 6 7 8 9 10 »   Go Up