Author Topic: Resonance WFC measurements  (Read 60760 times)

0 Members and 24 Guests are viewing this topic.

Offline Login to see usernames

  • Moderator
  • Sr. member
  • ***
  • Posts: 437
Re: Resonance WFC measurements
« Reply #40 on: June 14, 2011, 19:08:41 pm »
I'm talking about the Resonance WFC cell driver circuit, not a 8XA coil.

To make it more clearer see fig below.

Br,
Webmug

Offline Login to see usernames

  • Member
  • **
  • Posts: 184
Re: Resonance WFC measurements
« Reply #41 on: June 14, 2011, 23:21:46 pm »
gotcha, thanks for circuit diagram, I may try it anyway into my 3 inch, 1/2 mm gap tubes....  after my bifilar toroid

Offline Login to see usernames

  • Moderator
  • Sr. member
  • ***
  • Posts: 437
Re: Resonance WFC measurements
« Reply #42 on: February 22, 2012, 14:19:25 pm »
@Dave, All,

This is what I measured on a 10kV 1nf capacitor.
Could be the above 0V voltage that brings up the "above ground level".
http://www.ionizationx.com/index.php/topic,1305.msg22180.html#msg22180
http://www.ionizationx.com/index.php/topic,1305.msg22161.html#msg22161

PULSE TRANSFORMER The typical pulse transformer operates in an “unipolar” mode ( flux density may meet but does not cross zero ).
http://www.ionizationx.com/index.php/topic,1934.msg20298.html#msg20298

Br,
Webmug
« Last Edit: February 22, 2012, 22:44:22 pm by webmug »

Offline Login to see usernames

  • Sr. member
  • ***
  • Posts: 349
Re: Resonance WFC measurements
« Reply #43 on: February 22, 2012, 19:44:24 pm »
looks pretty good to me. So 500 volts or so is the highest you've gotten?
Anything special you did to get your singnal inverted like that?

Offline Login to see usernames

  • Moderator
  • Sr. member
  • ***
  • Posts: 437
Re: Resonance WFC measurements
« Reply #44 on: February 22, 2012, 21:41:46 pm »
looks pretty good to me. So 500 volts or so is the highest you've gotten?
Anything special you did to get your singnal inverted like that?
My chokes are not tuned, the voltage amplitudes are not equal but have opposite voltages when I vary the pulse frequency. I can not tune it with the pulse and gate signals. Chokes are not matched!
I tested this on a 10kV 1nf HV capacitor, when I use my wfc this waveform is not there. So the cell specs are very important to minimize leakage, I think...

Br,
Webmug

Offline Login to see usernames

  • Sr. member
  • ***
  • Posts: 349
Re: Resonance WFC measurements
« Reply #45 on: February 22, 2012, 21:54:15 pm »
Ok I see, I can get the correct waveform when I don't have the cell hooked up. The closer we get to what stan had the better at this point. If there is an unknown variable maybe we can stumble across it.

Offline Login to see usernames

  • Member
  • **
  • Posts: 270
Re: Resonance WFC measurements
« Reply #46 on: February 22, 2012, 22:35:27 pm »
Just curious, do you get the desired waveform from the cell being dry or without water in it?

Offline Login to see usernames

  • Moderator
  • Sr. member
  • ***
  • Posts: 437
Re: Resonance WFC measurements
« Reply #47 on: February 22, 2012, 22:42:01 pm »
Just curious, do you get the desired waveform from the cell being dry or without water in it?
Waveform above from 1nf HV 10kV capacitor.
Cell was submerged in tap-water no waveform.

Br,
Webmug