Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 »   Go Down

Author Topic: WFC VIC  (Read 290100 times)

0 Members and 230 Guests are viewing this topic.

Offline Login to see usernames

  • 50+
  • *
  • Posts: 99
Re: WFC VIC
« Reply #416 on: February 07, 2012, 16:48:16 pm »
IS it possible hat the square pc board on the right side of the vic coil cards in the control unit was designed t rotate the signals to each cell in a specific pattern to limit the power used..i mean when cell 1 was pulsing high cell 2 is halfway and cell 3 is just beginning , i find it interesting that there are a few 741 op amps 2wo plls and some gates...anyone have a clue to what that card is doing with all the other vic cards?
Logged

Offline Login to see usernames

  • Sr. member
  • ***
  • Posts: 460
    • Global Kast : Water Fuel Cell Research
Re: WFC VIC
« Reply #417 on: February 07, 2012, 17:20:49 pm »
in the VIC cabinet there were two other circuits, one for the "Steam Resonator" and another for the "Gas Processor". If I was a betting man, I would say the circuit you are referring to, was for the Gas Processor.
Logged

Offline Login to see usernames

  • Member
  • **
  • Posts: 238
Re: WFC VIC
« Reply #418 on: February 14, 2012, 00:58:37 am »
Anyone found a good place to get those plastic bobbins made up?

A while back someone on this forum gave me some info on a guy who was printing them. I sent him a requenst to have some printed up but I have never heard back from him.

I sent the dimensions to a local plastic printing place and they want over 100$ for a set.
Logged

Offline Login to see usernames

  • Sr. member
  • ***
  • Posts: 363
Re: WFC VIC
« Reply #419 on: February 14, 2012, 02:32:08 am »
Russ Gries just told me the other day that he knows someone printing them.Try his web site.
Don
Logged

Offline Login to see usernames

  • Sr. member
  • ***
  • Posts: 349
Re: WFC VIC
« Reply #420 on: February 14, 2012, 04:29:28 am »
Yeah, Russ got them printed from the same guy I pointed hms too who also made my bobbins. I think he might be a bit overloaded right now. Try the forum And if that doesn't work out, look for someone that does 3G printing, it costs so much less and I need more sets as well
Logged

Offline Login to see usernames

  • Member
  • **
  • Posts: 238
Re: WFC VIC
« Reply #421 on: March 21, 2012, 03:42:52 am »
Does anyone have the inductance measurements from the original 5 coil VIC with the core?
Logged

Offline Login to see usernames

  • Sr. member
  • ***
  • Posts: 460
    • Global Kast : Water Fuel Cell Research
Re: WFC VIC
« Reply #422 on: March 21, 2012, 07:58:38 am »
Quote from: Login to see usernames on March 21, 2012, 03:42:52 am
Does anyone have the inductance measurements from the original 5 coil VIC with the core?

Yeah here's the measurements that Don took from one of Stan's VIC transformers. Don has it listed as 29ga wire but 30ga wire has closer measurements to Stan's coils.
Logged

Offline Login to see usernames

  • Jr. member
  • *
  • Posts: 35
Re: WFC VIC
« Reply #423 on: March 21, 2012, 13:37:45 pm »
The only place I could find that is selling them online is here:
http://stansdream.com/stan_meyer_vic_bobbin.htm

Perhaps we could make them an offer?
Logged
Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 »   Go Up