Alternative Energy > Overunity devices

Magnet effecting Unipolar Pulses on toroidal Core

<< < (2/7) > >>

Steve:
Crazy video's!
If it was working, the whole world would run on it by now.
Does anybody seen a working model?

sebosfato:
Steve

I will measuring the output energy and input energy... i have only one multimeter so is going to be hard. I think that i will use a lamp as a load. than i will measure input and output current and voltage... Than there will be no doubt...

I discovered how to design transformers and now i'm finishing one with some taps in the primary for 20khz 120volts dc and will pulse it with my circuit than i will use the electron pump configuration (coil diode coil fields aiding) but with full wave bridge rectifier configuration, meaning 2 diodes 4 coils being two sets anti-paralleled, (doubling the frequency) than this (unlimited) voltage supply go to the the resonant coil with respective independent and isolated ground switches and collapse field voltage multiplier coil.

i mean unlimited by electron pump action it will pump amps with no limit in voltage so voltage is free to grow and grow...

unipolar pulses thus

To calculate the primary

remember that inductance = permeability of the core * (turns squared)     L=u*t^2
thus permeability = inductance / (turns squared)    u=L/t^2
And by consequence turns = square root of the (inductance / permeability)    t=sqrt(L/u)

And now you just need to know the saturation limit of the material in tesla and apply the following formula

turns=Volts/4/Area in m2/Hz/Tesla

t=V/4/A/Hz/T

m2 = cm2/10000 This is the area cross section of the core

For iron core 1 tesla
for ferrite from 0,1 up to 0,5 depends on the type

The secondary you need to choose the transformation factor and just multiply by the number of turns

you must consider the impedance of the circuit

the impedance transformation is = Z * Transformation factor squared Zt= Z*T^2

I wound the secondary series with contrary direction as to have both positive ends on the same side to void insulation problems. Hope it works..

sebosfato:
I found that the magnet dont cause mutch effect on this new transformer.. i believe that is because the primary winding is much wider than the other i tested before.. So the exact effect of the other transformer was having the primary about 3 cm wide and the magnet being 1cm  between north and pole...

I got the exact pulse wave form meyer showed... thru the water thought. Using the big green inductor connected the way i showed in that drawing... vic by sebosfato

now i just need to get into resonace...

I tried to attack on the 110 volts line but my dimmer burned in 5 seconds got also my irfp250 burned too... i will go buy a fuse and will connect straight to the line again=)... i will buy some of them...
And i need to go buy some more diodes and mosfets...

Is because i don't have a variac so im connecting straight to the line..

Steve:

--- Quote from: sebosfato on September 20, 2010, 21:20:17 pm ---I found that the magnet dont cause mutch effect on this new transformer.. i believe that is because the primary winding is much wider than the other i tested before.. So the exact effect of the other transformer was having the primary about 3 cm wide and the magnet being 1cm  between north and pole...

I got the exact pulse wave form meyer showed... thru the water thought. Using the big green inductor connected the way i showed in that drawing... vic by sebosfato

now i just need to get into resonace...

I tried to attack on the 110 volts line but my dimmer burned in 5 seconds got also my irfp250 burned too... i will go buy a fuse and will connect straight to the line again=)... i will buy some of them...
And i need to go buy some more diodes and mosfets...

Is because i don't have a variac so im connecting straight to the line..

--- End quote ---

Alright  Fabio. Closer then ever.
Maybe a scopeshot?????

sebosfato:
I went to the store to buy the diodes and the mosfet and i ended up buying some fuses and an igbt caled irgp30b120kd-e 1200v 30 amps

I was afraid that the irfp250 burned because a spike than i will find how to make a snubber well avoid burning this igbt witch was a bit expensive. .

I will solder everything up and i show you the scope

You will see the spikes... than

i need to add the second diode to create the step charging effect...

than is a matter of inputing voltage up to here the hydrogen will blow out of the bottle...

My friend engineer is going to make some tubes for me i think he will make three tubes sets with 1mm gap...

This way i can vary the capacitance...

The unipolar pulses are really interesting as seems full wave bridge rectified but the pulse is being generated by the collapse of the field in the coil.. as together with the spike...

shortly more to come

wish me luck