Author Topic: where to buy  (Read 17010 times)

0 Members and 1 Guest are viewing this topic.

Fiditti

  • Guest
Re: where to buy
« Reply #40 on: September 17, 2008, 14:09:55 pm »
Great job.  I'd love to see pics of your setup also.

Offline Login to see usernames

  • Hero member
  • ****
  • Posts: 657
Re: where to buy
« Reply #41 on: September 17, 2008, 22:37:14 pm »
alright i have to keep taking this with my laptops webcam....i don't ahve a digital camera....only medium format cameras!!.....so this is the transformer....if your wondering what the horrible plastic mess is it's my masking tape insulation.

(http://i2.photobucket.com/albums/y2/kinesisfilms/Photo7.jpg)

i will post photos of my entire setup when the bifilar coil is done.....i can post oscope images of the transformer but not until my roomate gets his cf card read working...so i can use his digital.

Fiditti

  • Guest
Re: where to buy
« Reply #42 on: September 17, 2008, 23:01:53 pm »
Very good job indeed.  It's very functional and not at all ugly.  That type of tape may give you some trouble.  You might want to use the special tape Bob Boyce recommends the next go around.  Great Job!!  Thanks for sharing the pic.

If you like, I'll try to run down the tape information for you.

Offline Login to see usernames

  • Hero member
  • ****
  • Posts: 657
Re: where to buy
« Reply #43 on: September 25, 2008, 21:00:40 pm »
alright so.....here is the core i am going to buy...1 inch in diameter is pretty hard to find.

http://www.stormwise.com/page26.htm

a pricey 91 dollars for a 1 inch diameter and 10 inches long.....i am making this real long becuase of what stan has said in his lectures.

Offline Login to see usernames

  • Hero member
  • ****
  • Posts: 657
Re: where to buy
« Reply #44 on: September 25, 2008, 22:05:42 pm »
sooo here is another site with the largest diameter being .5 inches.

https://www.amidoncorp.com/items/10

nvm i just realized that it has to be material 77.
so rods like this
https://www.amidoncorp.com/items/12

once again....nvm....just type in ferrite rod on ebay.

Fiditti

  • Guest
Re: where to buy
« Reply #45 on: September 26, 2008, 02:49:37 am »
kinesisfilms,

Thanks for sharing this information.
 

Offline Login to see usernames

  • Hero member
  • ****
  • Posts: 657
Re: where to buy
« Reply #46 on: September 27, 2008, 00:27:47 am »
alright so i got my pulsing dc and it is sent into the transformer at around 5 volts.....since my dc source is 12 votls and half on half off equals 6.......then it gets shot out the other end at a little less than 50 votls.....but at the frequency im using and the transformer im using it pulls around 1.35 amps naturally......i can't wait to get the bifilar core becuase i tried to do it with a gaint bolt and it wasn't a go.....too anxious...almost there and then step charging begins.
« Last Edit: September 27, 2008, 09:34:31 am by kinesisfilms »

Fiditti

  • Guest
Re: where to buy
« Reply #47 on: September 27, 2008, 02:14:02 am »
kinesisfilms,

I can't wait to see how it goes for you.