Stanley Meyer > Stan Meyers system 3

How to build the vic tried and tested

<< < (2/23) > >>

kickbackemf:
all,
I had been playing with some iron wire vics a ways back and was wondering how you guys keep em cool and not smoking the place up?
This info may have me return to the ideas I had using iron wire.  I'd like to find some teflon coated stuff.
I'm playing around, for observation's sake, with some soft iron twisty stuff that is paper coated and I coat that with varnish prior to wrapping a core....
 
kb
 
 

spintronic:
interesting, i guess u can see how even if the primary is not wound tight enough the inhibit choke reduces current?. If the secondary is wound and wired as tesla pancake coils further reduces current? As the primary warms and expands the current out reduces? the tighter the primary is wound the less current out. can you give us some more info on what you have been doing?
 
I have wound a small coil setup to test, its makes sense for the first go, if it did not work theres less time and effort put in. It did work, split water meyer style with tiny bubbles no gunk and zero current to the tubes. It was wound with a iron primary and 16v supply, it got warm but no smoke, what have u been doing to set the place on fire? Copper wire looks like the way to go for the primary with less heat from my first test and as soon as i get my winding kit made i shall post the results of iron v copper primary.
 
kickback the primary needs to be closely wound, thick insulation could cause problems and the paper may give capacitance between coils that may or may not be a problem.

spintronic:
I have just confirmed a earlier observation the iron primary induces over x2 more current than the same size copper primary. This has not been tested on a normal transformer just my vic with loose wound primary (leaky). I am not expecting much in replys so i will just say this, if you build a vic or anything based on technology like the 8xa circuit out of all copper you are wasteing your time, 4 years of building stuff that don`t work or of little use proves it.
 
Resonance has been a source of confusion with meyers patents. I have identifyed alterations in his patents and the use of resonance has been referred to in a number of places it should not be.
The resonance talked of in meyers wfc for example refers to the freedom of movement of hydroxyl ions in water that needs to be tuned into for high gas yield, this comes from a independent evaluation of meyers wfc. http://www.scribd.com/doc/36927148/WFCexpl
 
So much mis-information about meyers technology for so many years has left people not knowing what they are doing.
 
 

Steve:

--- Quote from: spintronic on August 14, 2011, 06:54:19 am ---I have just confirmed a earlier observation the iron primary induces over x2 more current than the same size copper primary. This has not been tested on a normal transformer just my vic with loose wound primary (leaky). I am not expecting much in replys so i will just say this, if you build a vic or anything based on technology like the 8xa circuit out of all copper you are wasteing your time, 4 years of building stuff that don`t work or of little use proves it.
 
Resonance has been a source of confusion with meyers patents. I have identifyed alterations in his patents and the use of resonance has been referred to in a number of places it should not be.
The resonance talked of in meyers wfc for example refers to the freedom of movement of hydroxyl ions in water that needs to be tuned into for high gas yield, this comes from a independent evaluation of meyers wfc. http://www.scribd.com/doc/36927148/WFCexpl
 
So much mis-information about meyers technology for so many years has left people not knowing what they are doing.

--- End quote ---

Hi Spintronic,

Welcome here at ionizationx  :)
I can follow what your are explaining here.
Is it possible that you publish some pictures of your iron wire tests? Maybe scope-shots?
Would help others a lot with getting an idea on what you are researching.

One question from me is about your statement to tune into the hydroxyl ion.
First, my idea was that in such setup, to tune into the H+ ion and not the HO ion.
Maybe you can explain why you choose the HO ion?


Steve



Mr_H2O_Splitter:
What kind of iron alloy are you using for the wire?

Soft magnetic iron wire seems to be hard to find.

Navigation

[0] Message Index

[#] Next page

[*] Previous page

Go to full version