General => General Discussion => Topic started by: Hydrocars on April 22, 2020, 10:05:33 am
Title: I Cracked it!!!!
Post by: Login to see usernames on April 22, 2020, 10:05:33 am
I'm Proud to say I cracked it all! No, I dont give one damn shit about any credit, Im just glad this shit is finally over with!!! I've been researching this technology between tesla and stan for 25 years or more.
I was going to make a youtube video because I did want the views, not sure how that pay tube junk works and Im limited on time being I can only test on the weekends.
I will leave you with this grain of salt, for one, Because what I'm about to leave you with is all you need to know. So here be the small sentances.
I used a Step up coil from a Central Heating and air unit, (The Gas Furnace Igniter) All furnaces doesn't have them. The secondary measured around 1k ohms. I used the Telsa Mini Circuit on the net that containes just 1 resistor, 22k, I used a 2A224J Capacitor between the Source and Drain of the IRF740, Any N channel mosfet should do.
Heres where it gets tricky, You use 2 diodes and connect them to the output of the transformer, (Led Light emitting Diodes work best) Connect one opposite than the other. Now you should have 2 unconnected Ends. (That goes to your fuel Cell). HOWEVER, the (Contactor switch) from a Heating and Air Unit, (COIL ONLY NO METAL CORE) shall be placed between a Single round Tube Cell about 2 inches tall or so and one of the Diodes. I did this on the Negative side. This Circuit is Dangerous!
Thats all, you can produce hydrogen with only 1 wire folks, Thats right (A OPEN CIRCUIT) Produces hydrogen.
Unfortanately, Mosfets cant handle whats needed to be done here, Tubes will have to be used later, Thats another day for me. Everytime I start getting good production The fet Blows due to the back emf getting to high. Also, you will not be able to touch the leades of the fuel cell, I had a arc go threw my finger and it burnt a hole in the end of my finger. These are Radio Frequencys so you dont get shocked anymore, you get FRIED!! You will smell your skin smoking and the room will be filled with Smoke from your finger, this damage only takes a Nano second so you cant avoid it, this circit is nothing to play with.
Also, I will leave you with this un needed information. Telsa make Electric moters, they was 1 2 3 and so HORSEPOWER. I will say this another way because my time is limited here, 1 Horse can Pull 8k Pounds, so this means 2 horses can Pull, yup, you guessed it, 40 Thousand Pounds or close to it! So yes, Tesla's HP Moters, I mean, Energy Converters are like that!
Tesla Used 2 coils to power his Ac Generators not 1, Tesla Knew about horses, he used a Symbolic 2 Horse Coil ( 3 to 4 times its Load) to puse it into a Ring of (Sets of coils) ontop of Sets of More Coils) to step Electricity around in ways that is not seen to man on this earth as this information is public but not understood. Anways, thats not really important, What is Important is you understand and learn how to connect an ac Output wires To itself and make it run on 1 wire!
I will say this one last time before I go, that water Fuel cell is a (OPEN CIRCUIT) , Thats how it runs, I Gaurantee you this is a fact, I Put it on my life!! I say this because I know for a fact because I have been producting hydrogen this way for sometime now. Do Expect me to come back and reply to this forum or dont expect me to answer any question at all, because it may be weeks or moths before I log back in to this site.
Just so you understand, 1 wire goes to 2 connecting diodes, the unconnected ends of the diodes go to a fuel cell with a coil their between with an (AIR CORE) and Leds are used for the Diodes, I tested this setup with stanleys diode and it would not work. and again, this Circuit is dangerouse!
I used a Vacriac as the power source, and I Rectified that, and used 2 big capacitors to smooth everthing out. Build the circuit, raise the voltage! And get ready to blow some fets! I've blown a ton on this, and if you think the fet is blown, dont be so fast about replacting it, Turn up the voltage High, High enough to make the fet revive itself. You will eventually learn the circuit works and that Fets are no good, then you will get excited about what your doing and start looking for new ways other than fets.
Your cell phones will not work with this circuit running, your laptop will malfunction. Funny things around the house will start to happen. This is No Joke. Good day!
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on April 23, 2020, 17:49:55 pm
This all sounds pretty good, but I don't understand the "single wire" part of it. Two diodes connected to the cell, one with a series inductor? Where's the open circuit? Are BOTH diodes hooked to the same transformer wire? If so, how is that the negative side? Is there a rectifier?
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on April 23, 2020, 22:56:45 pm
I will make a second post. With a video, then I ask you to share with as many people possible.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on April 24, 2020, 00:25:58 am
I'm starting to get a handle on this. Both diodes are connected to the same transformer wire, with the diodes in reverse polarity and the other transformer wire left open. The inductor is connected to the diode with negative polarity and the inductor's output is connected to the water cell, along with the other diode. The transformer isn't rectified, or fully loaded.
This is an innovative approach to the single wire circuit. Normally, both transformer wires are connected to a spark gap with an adjacent single wire electrode's circuit terminating on a polar mass. (Which in this case would be the water cell). With both approaches, the current flows up one side of the wire and back down the other side of the same wire. At high frequency, these bidirectional currents are simultaneous. Using the two diodes allows it to work with just one side of the supply, which is otherwise unloaded.
In my opinion this is a significant discovery.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on April 24, 2020, 08:37:17 am
Quote from: Login to see usernames
I'm Proud to say I cracked it all! No, I dont give one damn shit about any credit, Im just glad this shit is finally over with!!! I've been researching this technology between tesla and stan for 25 years or more.
I was going to make a youtube video because I did want the views, not sure how that pay tube junk works and Im limited on time being I can only test on the weekends.
I will leave you with this grain of salt, for one, Because what I'm about to leave you with is all you need to know. So here be the small sentances.
I used a Step up coil from a Central Heating and air unit, (The Gas Furnace Igniter) All furnaces doesn't have them. The secondary measured around 1k ohms. I used the Telsa Mini Circuit on the net that containes just 1 resistor, 22k, I used a 2A224J Capacitor between the Source and Drain of the IRF740, Any N channel mosfet should do.
Heres where it gets tricky, You use 2 diodes and connect them to the output of the transformer, (Led Light emitting Diodes work best) Connect one opposite than the other. Now you should have 2 unconnected Ends. (That goes to your fuel Cell). HOWEVER, the (Contactor switch) from a Heating and Air Unit, (COIL ONLY NO METAL CORE) shall be placed between a Single round Tube Cell about 2 inches tall or so and one of the Diodes. I did this on the Negative side. This Circuit is Dangerous!
Thats all, you can produce hydrogen with only 1 wire folks, Thats right (A OPEN CIRCUIT) Produces hydrogen.
Unfortanately, Mosfets cant handle whats needed to be done here, Tubes will have to be used later, Thats another day for me. Everytime I start getting good production The fet Blows due to the back emf getting to high. Also, you will not be able to touch the leades of the fuel cell, I had a arc go threw my finger and it burnt a hole in the end of my finger. These are Radio Frequencys so you dont get shocked anymore, you get FRIED!! You will smell your skin smoking and the room will be filled with Smoke from your finger, this damage only takes a Nano second so you cant avoid it, this circit is nothing to play with.
Also, I will leave you with this un needed information. Telsa make Electric moters, they was 1 2 3 and so HORSEPOWER. I will say this another way because my time is limited here, 1 Horse can Pull 8k Pounds, so this means 2 horses can Pull, yup, you guessed it, 40 Thousand Pounds or close to it! So yes, Tesla's HP Moters, I mean, Energy Converters are like that!
Tesla Used 2 coils to power his Ac Generators not 1, Tesla Knew about horses, he used a Symbolic 2 Horse Coil ( 3 to 4 times its Load) to puse it into a Ring of (Sets of coils) ontop of Sets of More Coils) to step Electricity around in ways that is not seen to man on this earth as this information is public but not understood. Anways, thats not really important, What is Important is you understand and learn how to connect an ac Output wires To itself and make it run on 1 wire!
I will say this one last time before I go, that water Fuel cell is a (OPEN CIRCUIT) , Thats how it runs, I Gaurantee you this is a fact, I Put it on my life!! I say this because I know for a fact because I have been producting hydrogen this way for sometime now. Do Expect me to come back and reply to this forum or dont expect me to answer any question at all, because it may be weeks or moths before I log back in to this site.
Just so you understand, 1 wire goes to 2 connecting diodes, the unconnected ends of the diodes go to a fuel cell with a coil their between with an (AIR CORE) and Leds are used for the Diodes, I tested this setup with stanleys diode and it would not work. and again, this Circuit is dangerouse!
I used a Vacriac as the power source, and I Rectified that, and used 2 big capacitors to smooth everthing out. Build the circuit, raise the voltage! And get ready to blow some fets! I've blown a ton on this, and if you think the fet is blown, dont be so fast about replacting it, Turn up the voltage High, High enough to make the fet revive itself. You will eventually learn the circuit works and that Fets are no good, then you will get excited about what your doing and start looking for new ways other than fets.
Your cell phones will not work with this circuit running, your laptop will malfunction. Funny things around the house will start to happen. This is No Joke. Good day!
Thst sounds promising, Brian. I cannot wait to see yr video on this. Well done!
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on April 24, 2020, 10:19:58 am
feature=emb_logo
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on April 24, 2020, 11:18:03 am
I think it's time to show it working the way you said it does, without "free energy tricks".
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on April 25, 2020, 10:03:56 am
Stevie, that might work, test it and let me know, X-Blade, I'm very sorry as my time is very limited as stevie can explain, as his is to. I mean no offense when I say I have a life. Patience! You will have your video proof in about 45 minutes... guys, please understand the future is in your hands not mine, I can't test this technology the way some of you younger guys can, hey, I'm counting on allot of you guys here to finish this!
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on April 25, 2020, 10:32:14 am
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on April 26, 2020, 08:55:58 am
Thank you for the video! My first impression is that it looks very similar to the Stiffler circuit with these two diodes. Stiffler also worked on the one wire power transfer.
Great stuff
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on April 26, 2020, 10:09:08 am
I suggest paying stiffer more attention! I'll look him up. Invite him here.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on April 26, 2020, 21:48:06 pm
I don't see any relationship between this and Dr. Stiffer's free energy claims. This is something new. It's not even related to the Avramenko diode plug. Attention should be given where it's due. Otherwise, what's the incentive for posting at this site?
And hasn't Stiffer already snubbed an invitation to come here?
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on April 26, 2020, 22:59:58 pm
i just send him a comment on his youtube channel... Maybe he comes...
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on April 26, 2020, 23:02:26 pm
I'm planning on making a bigger version of this, in my video I didn't have it turned fully up because I didn't want to blow the mosfet. The rf burned is the most brutal burn I've ever felt, it leaves a black hole in your finger and theirs no avoiding it if you touch it. The leads of the fuel cell has kilo volts on either tube. It's not operating from a low voltage. My next step is to use tube now a few, and I want to try a transistor. I have no clue how to connect these tubes or even how they work. And thanks Tectrical!
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on April 27, 2020, 00:35:04 am
I'm wondering: if touching either Cell electrode results in an rf spark, what will happen if an additional polar mass is connected to one of the electrodes? This would be a single wire leading from the cell side of one of the diodes to something like a MOT core. Or perhaps to a single electrode in a second Cell. Remember that a human body is essentially a polar mass itself.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on April 27, 2020, 04:50:16 am
and yes, it does!
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on April 27, 2020, 06:32:39 am
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on April 27, 2020, 13:11:58 pm
Brian, those are very very cool test,s you did. I am proud on you. Never give up, i would say. You are the first showing high voltage on the electrodes of a Meyer test setup. I never seen anything like this before.
My comments : i think that your coil between the cell and diode, is picking up power from the secondairy. That closes that part of the circuit.
Question: can you try separating the cell with diodes and coil , from the high voltage transformer? Just use a long wire between them. At least 2 meters would be good. I wanna know if you see bubbles with that distance..
Man....!!!! Wow!!! Those sparks show a voltage of at least 10kilovolts....
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on April 28, 2020, 17:13:54 pm
I finally fried that mosfet last night the one in the video I believe it's a 13 45 or something another of that nature anyways I compared it to another one by installing another smaller mosfet like seen in the original videos let me tell you what those small mouth puts blow almost every time the resistor and one of the original videos was in the wrong place I was only following the meaning Tesla circuit eventually figured it out and moved it over from the gate to the source it's a 1 million Ohm resistor and that is where it belongs however sometimes I have to put my finger on the resistor to get the circuit 2 resonate. Also I was able to light a 12 volt light I'm the secondary call by connecting a lot between. Cole and the primary I'm talking about the coal in series with a fuel cell the secondary call lead what's left on connected on one end and I was arcing it on either of the other call that was in series terminals and with a right Arc a 12 volt light will light and the amp draw only went up 20 ma.
I do believe this circuit should be used to convert energy and not for a fuel cell I think the fuel cell is connected too soon in the circuit I also think this should be a wireless system with that being said you could now draw and imaginary circuit were they fire stats in resonance in the second goes to the fuel cell I believe this will give you the full 360 Degrees rather than the 180 degrees I feel like I am getting now. Sorry sorry about the typos it is a text-to-speech cell phone error it's either that or not posted off sitting in the parking lot of a doctor's office. I have many formulas I have gathered up over a great deal of time reading and researching I will scan these formulas if anyone is interested it is the master of resonance equations that I have put together one by one and they are all correct. I'll have all sorts of equations I'm about five sheets of paper I have taped on my wall if anyone wants them feel free to ask and I will post them somewhere here I will post them anyways like her own when I get time and if anyone has any problems with a formulas I will also post a how so you use them and anyone here that stuff used on the equations will no longer be confused cuz I will break it down really simple so everyone can understand how the form was work. Also also Stanley mayor has some form of in his patent and he says the dielectric properties of water is 78 arms meaning that is the capacitance reactance is 78 ohms with that being said it would only be true if the inductance reactance was also 78 ohms. Stanley walk Stanley walked around preaching 20000 cycles per second so with this and the end credits and capacitance reactance we are now able to check they circuit to see if it reacts is 78 or Twenty Thousand cycles per second using these formulas. I will I will upload a few videos on how to use these formulas to make it even simpler so if you've never done it before I will tell you now it's nothing don't sweat it these are very simple equations that I will teach you how to do.
One last night Tesla has some missing equations and I believe we can find them. If you if you search for Tesla on Wikipedia you will see patents in those patents you will see a energy converter that is on a round ring and in another patent you will see how he supplied the voltage with a twin to horse call where it is not labeled that. it is possible whoever stole the patents did not realize how powerful this patent was I think it is a leak. I will end this post saying Tesla's low voltage primary was very fine wire and the secondary was very coarse and it was wired on the outer side of the fine wire on a toroid. This is completely backwards from the Tesla coil. Also he does everything in sets of two's there is many different ways to hook the coils on the toroid as explained in the patent. Hey refers to this as a energy conversion machine that can be used in multiple ways and he Powers it with a twin horse coil. This is why I was saying one horse can pull 8000 lb into horse can pull 40,000 lb if you can understand that pick a pair that with these dual coils then you can make the equation they do not know enough to even attempt it at this time because all of these energy converting devices uses radio frequencies and not anything below 100 Hertz.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on April 29, 2020, 18:03:31 pm
Hi Hydrocars,
If i understand you well, you say that the Tesla setup is creating more energy then you put in? Its like opening a gateway?
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on April 29, 2020, 23:38:40 pm
Radiant energy Steve. I'm working threw resonance and Tesla's building resonator is related, I'm surprised what can be done with just 1.5 volts at the moment. I'm in deep research at this time. I will share all my findings.
I can't wait to see someone confirm this above circuit.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on April 30, 2020, 09:24:16 am
You put 1 volt in that mini Tesla?
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on April 30, 2020, 19:59:41 pm
I doubt that, probably 35 I didn't measure, I haven't took anybmeasurements, I was so excited about hydrogen production with 1 wire. The wattage had to be low. I don't care if it was a hundred amps of current I don't care if it was 300 I'm just impressed with someone wire production...
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 03, 2020, 02:37:26 am
Radiant energy Steve. I'm working threw resonance and Tesla's building resonator is related, I'm surprised what can be done with just 1.5 volts at the moment. I'm in deep research at this time. I will share all my findings.
I can't wait to see someone confirm this above circuit.
I don't think the circuit has to be confirmed; it's basically an energy harvesting circuit with Stan's inductor added in. But I am working on it. What I'll try is one wire from a CFL.
I think the best part, besides getting the bubbles, is that you discovered LEDs work as high frequency diodes. I wonder if the circuit can be powered with rf from an antenna.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 04, 2020, 20:08:45 pm
I collected some parts for replication Brian. Soon i must be able to smack it together... ;)
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 06, 2020, 23:13:45 pm
Look closely at that fets data sheet I used, it seems to work best. And that's cool on the led part tektrical! I can't wait to see you guys better this.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 10, 2020, 00:58:36 am
My first attempt failed with getting a mini tesla circuit working... Maybe my transistors are no good or my secondairy coil.... Monday i can get me some transistors.... The one i used sofar: Ksp44 C945
Primary coil is 3 winding Resistor 22k
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 10, 2020, 04:40:00 am
1m resister between gate and source/ground. May have to touch resister at gate as you increase voltage. Let go when leds light up. Do not over ramp the voltage until you become experienced at this circuit. Let run with leds lift for 10 mins or so. If no production swap cell polarity.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 10, 2020, 22:22:53 pm
Jippyjee
The tiny transistor gets hot.... The lightbulb gets on So, at least a babystep has been taken. This tiny tesla does not visually ionize the air, but the gas bulb shows a radiant field of energy!
Now i have to find more leds and a heavier npn...
Cheers Brian!
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 10, 2020, 22:29:00 pm
My unit is getting close to the testing phase. A lot goin on, but if I can squeeze one thing in each day on this, pretty soon it'll be sitting there.
I verified the fluorescent driver works, and the flashlight LED assembly is ready. I dug out a relay which looks like the one in the video. It's rusty and getting the little steel plunger out will be about the last challenge. Then it's just wiring it up to a cell and seeing what happens.
I can see a lot which might be done with this new circuit, and I may even test my new single-phase shape resonance diode.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 11, 2020, 19:58:49 pm
I am glad someone is testing a transistor my only Wonder is a mosfet is voltage controlled and very sensitive to the resident of feedback of the coil and the transistor is current regulated at is Skate rather than voltage like the mosfet. Maybe this will work out better let me know.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 11, 2020, 21:14:57 pm
It works now much better. I got some highfrequency switching high power transistors.... That works! The circuit is still a little onstable, but stable enough for the coming tests.
Here another video... A 8 watt tl bulb goes fully bright The circuit does 18v on 0.3 amps.
When i touch the solder on the plus wire, i get jolt... See also how the bulb is still shining when it goes over the batterys... As the whole circuit goes Tesla....and radiates...
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 12, 2020, 17:34:28 pm
I burned my skin... First hho from 1 wire And more wierd things...
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 12, 2020, 17:49:25 pm
And then i saw a stream of hho...and then the batterys got empty....
I will get a powersupply in here.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 12, 2020, 18:55:09 pm
And there it is...the old works best...
Do you want to see HHO production Tesla style? Watch this... 9volts and 0.4amps
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 13, 2020, 20:15:23 pm
Hell yeah! I'm impressed!!!
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 13, 2020, 22:12:36 pm
The next question is......what to do next...
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 13, 2020, 23:37:42 pm
You might try using a cluster of parallel LEDs for each of the diodes. A cheap flashlight has nine. You could judge how bright they are, and see what effect the lower resistance has on the gas production.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 14, 2020, 13:52:49 pm
Make it better! It's small scale, get some resonate coils in parallel, start tweaking. I haven't had a chance to look at the driver stevie used. The frequency may can be altered.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 14, 2020, 16:15:11 pm
And, of course, make sure the bubbles are flammable, not just steam being liberated.
I'm starting to spend more time on this project, now that my understanding of the importance of the new circuit is increasing.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 14, 2020, 20:46:27 pm
I tried to burn some bubles. 50 times nothing and then just one time a tiny pop.... Not sure what i am producing here...
Thanks, btw, for your suggestions..
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 14, 2020, 20:51:02 pm
I changed the leds for super fast diodes. The results are the same. Adding a coil or capacitors didnt improve. So i doubled my secondairy coil in size. That gave me higher voltages. Results in bubles a bit better. But not really hho pops after ignition...
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 14, 2020, 22:17:23 pm
Laser pointer diodes, shining between the plates?
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 16, 2020, 05:01:16 am
3 6 9 Tesla, if you understood that, then you could hold the keys to the universe.
Stevie, Add a second Mini Tesla, While you are doing that, Also look for the eleventh harmonic.
Be sure the second Mini Tesla is not identical to the first, as your not looking to boost power, but to apply a second frequency to the water. When Coil 1 and Coil 2 is at the tuned frequencies the water will generate the Third harmonic on its own.
However, if one wanted to skip the above, Increase the size of the Tesla coil, Add a second Mini Tesla identical to the first using a seperate Isolated power source.
A tesla coil should be designed so that it could be Tuned, as so for the second. There will be an eleventh harmonic at every frequency. Which of those tuned frequencies does water react to? Well with my Mini tesla when I put my hand on the glas container, I could feel the water Thumping the Container as if it was Pulsating in a way it could Bust the glass. Try feeling its heart beat on the external part of the glas stevie. Put your hands on it and feel it pumping the glass jar.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 16, 2020, 20:21:22 pm
thanks guys
I will continue testing......
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 16, 2020, 21:06:33 pm
I think the best thing you could try would be to pulse the input to the driver, on and off.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 17, 2020, 09:43:11 am
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 17, 2020, 13:45:09 pm
Brian, if i understand your video explanation, you hook up a squareware function generator positive output with one lead to that tiny bif coil and then from there is one wire going to the diodes and cell. I am correct here?
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 17, 2020, 15:05:23 pm
Excellent video Brian. Thanks for all the screen shots.
Here's some more math: One Coulomb equals 6.24 X 10 .exp. 18 One mole equals 6.022 X 10 .exp. 23
Therefore, with one electron per molecule, there's roughly 100,000 Coulomb per kg of water, which is one liter. So we need .01 ml of water to get one Coulomb of charge.
But shouldn't you put that coil in a Faraday cage, to rule out an antenna operation, before concluding it's ZPE?
At any rate, the coil produces a biphasic signal. And so will my hairpin capacitor. (Shown in reply #32 on page #5).
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 17, 2020, 17:13:32 pm
Brian, if i understand your video explanation, you hook up a squareware function generator positive output with one lead to that tiny bif coil and then from there is one wire going to the diodes and cell. I am correct here?
yes, sinewave.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 17, 2020, 17:18:12 pm
Excellent video Brian. Thanks for all the screen shots.
Here's some more math: One Coulomb equals 6.24 X 10 .exp. 18 One mole equals 6.022 X 10 .exp. 23
Therefore, with one electron per molecule, there's roughly 100,000 Coulomb per kg of water, which is one liter. So we need .01 ml of water to get one Coulomb of charge.
But shouldn't you put that coil in a Faraday cage, to rule out an antenna operation, before concluding it's ZPE?
At any rate, the coil produces a biphasic signal. And so will my hairpin capacitor. (Shown in reply #32 on page #5).
I'm not sure at this point, nothing done here is normal. You can see results without a coil it's just far weaker and takes longer. My cell is running all night, has a steady stream now. But it's still a barely visible stream. But it is a stream that's free. I want a faster generator. I can't test above 20Mhz but in running at 1.8 mhz at the moment.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 19, 2020, 06:57:03 am
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 20, 2020, 18:07:27 pm
I'm aware that rotation is considered as being a property, rather than a movement. But if something is rotating faster than the speed of light, individual points would still move faster than light and the rotating system would move outside of the universe.
That's not the key to antigravity.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 22, 2020, 11:45:37 am
HI Brian,
Thanks for your video and explanation. I can see that you have spend lots of time on this. To understand with what kind / type of electricity you and me are dealing with, i have included another video. Its the old borderland video of Eric Dollard explaning the two wave forms TEM and LMD transmittion waves. TEM is electricity as you know it. Electromagnetic waves. LMD are the longitudinal waves which a Tesla coil is producing. A coil is capacitance and inductance at the same time.... Please watch this video till the end.... And again and again....
feature=youtu.be
Cheers
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 22, 2020, 19:06:28 pm
I wonder if this energy Dollard discusses will disintegrate matter, the way Tesla used HIS longitudinal waves to clean a metal film from the inside of a vacuum tube by converting the deposited metal into longitudinal mass?
A Tesla coil CAN produce longitudinal waves, but it would need TWO primary windings, tuned to slightly different wavelengths. Otherwise, what you get is unidirectional, but not longitudinal.
edit: Why was it that Dollard was never able to replicate Ed Gray's Power Conversion Tube, which is based on Tesla's longitudinal wave techniques?
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 23, 2020, 23:47:40 pm
He was living in a car for some days....Maybe thats why.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 24, 2020, 01:57:25 am
He was living in a car for some days....Maybe thats why.
And he probably is again. I'll tell you why, and it's because he's trained as a modern day EE. He doesn't know half of what the original Radio Men of a hundred years ago knew. What's the value of dumping his theories into this discussion?
Here's a thought: anything which gives off Longitudinal Energy experiences a recoil, due to environmental reaction. Why not suspend one of the LEDs from a plumb bob tether, pulse the Tesla coil, and see if the plumb bob moves a detectable amount. If it doesn't, then either your measurement isn't sensitive enough, or there ISN'T any LE.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 24, 2020, 02:42:08 am
That sounds interesting!
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 24, 2020, 15:29:10 pm
Someone posted to Keelynet early on that a red LED was attracting a strip of toilet paper. He didn't show his circuit, or say if he had a vibrating metal plate adjacent to the beam, charged or otherwise.
edit: With LE, I would think the plate should be magnetised.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 25, 2020, 09:01:13 am
You both are missing the point here. If you watch that video you would have seen two setup with LC circuits. What would happen if you replace in the last setup the capacitors with two watercapacitors?
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 25, 2020, 14:36:43 pm
Is he still using parallel inductor runs bridged by capacitors? A two wire circuit?
Look at some crop circle pictures, with increasing/decreasing polar capacitors, each branch a single 'wire' conductor.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 25, 2020, 18:28:38 pm
I'm sorry guys I have not had the time to properly read over this thread but I will very soon I am busy cleaning up the yard and preparing for more court cases.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 25, 2020, 20:28:58 pm
I've been very busy too. I'm thinking about pulling back for a while.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 28, 2020, 08:30:54 am
A bi-filar coil has an output which contains two different phases. The phase angle depends on the relative lengths of the two windings. With both wires the same length, the phases are at 180. The output wire could keep on winding, by itself, until that wire is, for instance, a quarter wavelength longer than the input wire which is wrapped side by side throughout its shorter length. Nikola's patent shows the outer wire extending an extra 90 degrees around the perimeter, but this doesn't necessarily give rise to a 90 degree phase difference in the signal. That wire could wrap on around a couple of times, or more, depending on the desired phase variance, and the overall wire lengths.
When both wires have the same length, running the single wire output through a full wave rectifier will double the intensity of the potential. Or a single LED on the output will chop the bottom of the phases, leaving the same biphasic frequency. (With a DC offset, both complete phases will pass through the cell).
The effect the phase variance has depends on the substance. A given substance will require a characteristic phase angle. If all you want is a longitudinal wave, use 90 degrees. Then each molecule will experience a field which compresses, then expands, as each wave passes.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 28, 2020, 13:47:26 pm
A bi-filar coil has an output which contains two different phases. The phase angle depends on the relative lengths of the two windings. With both wires the same length, the phases are at 180. The output wire could keep on winding, by itself, until that wire is, for instance, a quarter wavelength longer than the input wire which is wrapped side by side throughout its shorter length. Nikola's patent shows the outer wire extending an extra 90 degrees around the perimeter, but this doesn't necessarily give rise to a 90 degree phase difference in the signal. That wire could wrap on around a couple of times, or more, depending on the desired phase variance, and the overall wire lengths.
When both wires have the same length, running the single wire output through a full wave rectifier will double the intensity of the potential. Or a single LED on the output will chop the bottom of the phases, leaving the same biphasic frequency. (With a DC offset, both complete phases will pass through the cell).
The effect the phase variance has depends on the substance. A given substance will require a characteristic phase angle. If all you want is a longitudinal wave, use 90 degrees. Then each molecule will experience a field which compresses, then expands, as each wave passes.
So well written. Thank you, Tek.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 29, 2020, 22:28:34 pm
Thanks, Steve. Of course, if you do extend one of the bi-filar windings, you might need to bridge that part of the coil with a trimmer capacitor, for the desired phase shift. It would help to look at it on a scope.
And I don't see why longitudinal waves won't stretch a polar molecule, with the back of it anchored by a static charge.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 30, 2020, 10:12:55 am
That sounds hopefull ;)
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 30, 2020, 10:13:44 am
I think that LWaves might be the key in efficient gas production.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on May 31, 2020, 23:29:53 pm
Thanks for your video and explanation. I can see that you have spend lots of time on this. To understand with what kind / type of electricity you and me are dealing with, i have included another video. Its the old borderland video of Eric Dollard explaning the two wave forms TEM and LMD transmittion waves. TEM is electricity as you know it. Electromagnetic waves. LMD are the longitudinal waves which a Tesla coil is producing. A coil is capacitance and inductance at the same time.... Please watch this video till the end.... And again and again....
feature=youtu.be
Cheers
what are longitudinal matter waves? the electron doesn't produce any magnetic field on it's axis of movement so there are no EM waves on the longitudinal axis , the EM waves come from relativistic effects and contraction/dillation happens on the axis of movement so any effect manifest perpendicular to this in the transverse direction aka EM waves
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on June 13, 2020, 23:08:33 pm
I still haven't had time to get back to any post here but I will in time maybe a week or two. I'm deep in politics at this moment and at this time I have poweful people coming into my home monthly and looking around and there's nothing I can do about it. I was told if I gave any trouble or refused anything my children will be put in a foster home and taken away from me so at this time I am being threatened, I am not the kind to let stuff like this slide so simply put I will not be hushed!
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on June 28, 2020, 21:32:40 pm
I did some tests in this direction few years ago.. i was hoping that the cells were going to create a current that would sustain...
did you tried morephases it was going to be my next step than at the time but i had many theories to go and test less than 10_% of them ...
i would get a acrylic cup sand it inside and outside and apply some graphite from a pencil like on the outside and than place an aluminum foil on outside...
you will see a much more pronounced effect and more
you will see the gas bubbles flying around the top really moving... at the time i pulse it with a step up transformer than i had this two diodes on both sides of the transformer going to two coils and connecting coils to the cell.. one side of the secondary was connected to the foil on the outside...
today i would connect a center tap of the secondary and see what happen...
i was very busy trying to develop a medical device for this covid 19 emergency and i came up with a very nice monitor of pressure flow and volume that might be use full for our experiments and is way cheap to build... i will give all the code for it open source on my google drive here for you guys .. the whole pulmonary ventilator is almost ready but the code is already useable... just need few tweeks and is done.. it just need a powersupply, sensors, a esp32 controler and a nextion screen... it can also command servos to control flow, open close etc... hope you enjoy =D
im trying to put things together to do some test too soon... this project will end soon with goodnew i hope!
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on June 30, 2020, 16:44:55 pm
I'm glad to hear you are a coder sebo. Unfortunately I code in assembly which I find the easiest understood and the most straightforward not sure where you use. I have written a cold for the atmel AVR in atmel studio and I have been able to monitor a coils Behavior. It is very strange you bring this up because I was going to post this today anyways. This chip I have program monitors a coil and I have found that to get a coil to resonate you have to send square waves only not triangle not sine waves to get the coil to resonate at itself frequency. I would like to share this in case I died or something and I want this pointed out and I want special attention brought to what I am about to say. So please give the following special attention.
When you pulse a coil and you see a ringing wave after the square wave and they are perfect ringing rigs that is that coils resonant frequency. They can call it ringing all they want and teach that it is indeed ringing and not a resonant frequency but I decline 2 agree with such rubbish. As a tester an experimenter I can tell you the ringing frequency is a self resonance they coil is behaving at.
I will also share a coil does not like for the resonant frequency determined by the Bell ringing to be reproduced back to itself it is stubborn like a mule. I have obtained and recorded a coils resonant frequency and replicated that frequency and played it back to the coil to ring that coil and they coil will refuse to respond. I have found that just about a square wave at a very wide range of frequency will cause any coil to ring in this way especially around 100,000 Hertz of a square wave. This is indeed the latest of my findings and I could have never found this if I would have never programmed the atmel AVR are to help me pinpoint where residents is in a coil so this I do share.
I found the following video on YouTube the very start of the video shows you what ringing I am referring to I'm not sure what the rest of the video is about.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on July 09, 2020, 06:09:07 am
I had some equiptment malfunction, so i'm not sure sure the above post is exactly correct on the bell ringing, Im limited on time. more on this later.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on July 25, 2020, 11:35:42 am
If you see a ringing after the pulse, you must find out the reason. I have seen ringing because of the capacitance of my mosfet..... Thats why i recommand everybody to use the good old 2n3055 transistor.. Forget that shitty mosfet.
Title: Re: I Cracked it!!!!
Post by: Login to see usernames on December 06, 2022, 03:25:46 am