Ionizationx: a clean environment is a human right!

General => General Discussion => Topic started by: Steve on August 18, 2019, 23:08:38 pm

Title: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on August 18, 2019, 23:08:38 pm
Dear all,

Many of you have researched pulsed electrolysis and many made PWM,s or Dave lawton 555 timer schematics.
Here is the knowledge i have when you talk about which frequency to use.

Based on known patents and writings on forums etc etc etc.
Brown,s gas or whatever you wanna call it, is made with a pulsed system which should not exceed 200hz.
Horvarth systems do not exceed 166hz
The reason is that when you go higher in frequency, the induced current in the cell will adapt  an AC current characteristic, which will retard electrolysis.

Now many want to know which frequency Meyer used and even Dingle.
Well.....if you choose a frequency higher then 200hz you get this phenomenon of ac current character.
Meyer used that characteristic to setup a resonance system.
So, the frequency for a meyer techno system is based on L and C
I have seen and observed that AC current.

Well, i hope you can do your advantage with this

Steve



Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on August 19, 2019, 06:04:16 am
I think the frequency parameter is related to the spacing between the plates.  The Pat5 document from the group's Files Section details a system running at 1.1 MHz, with a gap of one tenth mm between the plates, using a bifilar coil, with the second winding connected only to the cell.  I also read another report which claimed this frequency was overly efficient.  The 555 itself will produce issues at its high end, which is two or three hundred kHz.
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on August 30, 2019, 23:19:57 pm
I will update this thread before the day here in the Usa is over. Please do not Criticize me for the documentation I am about to share with you all.
In just a few Hours from now, you will understand in detail how to harness a wealth of energy, and you will gain tremendous amounts of knowledge about the secrets that have been hidden for so long now. All though it has been right in front of your face the entire time, No light has been shed upon it. The curtains is about to open here in this thread. Thank you stevie for your very well put post! And as you will gain understanding, you will see then why the frequency is so important.

I am very sorry to hijack your thread, but I would rather get this out, and do this here, than create another thread of my own. Please get ready to print what I am about to post off, as it is very valuable, and it is really going to piss allot of people off.
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on August 31, 2019, 00:00:05 am
Make me proud, Brian!
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on August 31, 2019, 04:25:03 am
I am not perfect. I am not withholding anything at all. I say this because There me be errors in my work, meaning for example. Most use P Channel fets for Step downs, I do not. My Goal here is to give you an ideal, not try and mislead or hide anything at all. I would also like to add, I am very limited on time. With that being said, I will not be able to stick around and answer many questions. For those that want feel butt hurt because you do not feel this is what stan was doing - thats totally ok and I understand. I want be around to argue with you. I do what I can and I share what I can. Perhaps someone out there may make the best of this stuff. I am sorry if my documents offend anyone, that is truly not my goal here.

This technology never ends, and it is not new. Infact, it is old as tubes, if not older.
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on August 31, 2019, 08:34:48 am
This coils diameter is about the size of a penny, and wrapped around a ferrite core, the wire size is about 4 or 5 times bigger than the hair on your head, it measures 52 ohms. The gas production is not normal at all for only 2.5 volts 30 milliamps, this is just not normal!

Thought I would share this since I was experementing with my old single 555 pwm, I have that of lawton, one timer, 10k ohm on gate of fet to ground! both 200k pentameters. one pot only needs to be 50k but 100k is overkill on one, underkill on the other.

I really hope someone has fun with some of this amazing, unusual stuff. I have to admit, I dont know what the hell I am doing at all, I am just playing around and stumbled upon this. I still have not tested bigger coils. This coil gets fairly warm, no where near hot. "Almost hot" its heated but not hot. 

0.03 amps to cell, 3.47 volts lol, 0.1041 watts haha
0.08 amps 12.62 volts input to circuit 1.0096 watts

its more power in than out but why is it making hydrgen? and a good amount pretty steady bubble action too!

I put my finger between the positive terminal of the fuel cell and the positive terminal of my power source when I was trying to put my amp meter in series with the cell, and it shocked the living tar out of me!
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on August 31, 2019, 09:04:13 am
can you post a video of the gas production?
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on August 31, 2019, 09:56:40 am
Yes
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 02, 2019, 13:38:20 pm
Yes

Thanks!
What does your scope say, when you hook it up to the cell?
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 03, 2019, 19:04:43 pm
I got a resonance using Stan's Vic and didn't know till later, I have to reconstruct the Vic and try again and post. It was a low scale, I could tell it needed tweaking. There is something there. I had accidentally stumbled upon it when I connected 2 similar but HV could on the Vic with a shunt coil, it fried my timer.
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 03, 2019, 22:07:06 pm
frying is what we do... :) ;)
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 04, 2019, 01:07:13 am
 ;D :D ;)
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 07, 2019, 17:33:07 pm
Ive been hitting very high frequency with step down transformer with promising result. More later.
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 08, 2019, 06:33:09 am
Guy's I've been researching Step Up and Down DC to DC converters, messing with the PWM and the cell and let me tell you this! There is something there I can assure you this for a fact!
I would like to also add, Before stan ever started his water fuel cell research he was put a giant magafine glass at the top of a silo and tried to heat water in a pipe! He was trying to provide a small town with hot water then something happened and he stoped and started on hydrogen. Let me point out stan was searching for Green energy and I think he ran across the DC to DC being he was already interested in solar power and green energy.

I am telling you all, I think the heart of this technology is in the DC to DC and frequencies. I've seen it work both ways, stepped up and down. I've produced hydrogen with a coil wrapped only a few times at radio frequencies and also lots of times.

The PWM, it should be better understood why he was using a PWM, if you look at these DC to DC devices, you will See why the PWM matters.
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 08, 2019, 06:39:12 am
Stan was using a Power Point Tracker! That was His Feedback Coil! I know it!
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 08, 2019, 06:40:59 am
I blew a 10 amp Shunt Diode, and I'm just getting started!
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 08, 2019, 07:16:35 am
More power is Produced than Consumed, For those that do not belive me, Ask stevie. Or shall I ask him here.

Stevie, I have a Question for you here.

Do you have to use an external Power Source to Produce hyrogen or electricity to the alternator? Or, can it be triggered without any external Power? Also, Remember back when We was Exciting the Roter with a battery just before we would Test this Theory. Could you tell the members here a little bit about what you remember?
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 08, 2019, 07:25:42 am
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 08, 2019, 07:27:25 am
For those that does not know,
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 08, 2019, 08:06:30 am
I have came to understand stan, when he states, you must use voltage to perform work, just as you would change the color on your tv, in other words, he is saying remove all contaminates from the water and use a Dc to Dc step up circuit to prove his theory. He was offered 250 million dollars to just stop his work.
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 08, 2019, 11:51:51 am


Just watch this.....
This is what you want to do, i think..
Its called a boost converter.
This guy is lighting a 12v led on a 1.5v battery.
The coil gets charged first and then the coil discharges, plus the 1.5v of the battery in series.
So shortly you get and power boost, so to say..
It is fun to build.
I once made one with a wfc,
I always wanted to go back to it again...

Remember that circuit we build that showed more power out then in?
Thats the other variant....
Charge the coil and cell, switch off and part of the bifcoil got its charge from the cell and then power on, double power to the cell....

With a low resistance watercell, you might need to add a second transistor. 1 extra after the diode. So, one that breaks the connection to the capacitor...when you switches on the other transistor for charging the coil.

Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 08, 2019, 11:54:50 am
remember Pochintwin?


He replicated our circuit and he used a big bifilar toroid....

I have still all his data.

Like 350w in and like 500w into the cell

Or in his other video 60w in the circuit and 220watts out...in the cell....Brutal
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 08, 2019, 19:50:39 pm
can you post his circuit?
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 08, 2019, 21:52:58 pm
2 things are going on here, we use high amp draw like in your last post, and Stan explained you only need voltage. Both are acceptable in my book. But the alternator looks to be DC to DC.  And more power is produced than consumed if you do not include the driver moter.
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 08, 2019, 22:27:30 pm
I have came to the conclusion that on stans system, he is using 2 chokes on 1 core. Biffilar or the like. I now understand that he used the choaks in such a way that they Cancelled Each other out in a way that Prevents Amp Flow. Now I understand I never experimented with this type of configeration because then it made no sense, and the times that I did I got No gas production because No current would Flow. Now I understand that if you Hit the Resonate Frequency of the Chokes, Voltage Potential will Clime above 100k Volts, and this is when the water modelcule gets shreaded apart by voltage. I will do more Experiements on these Chokes, We Know Stan pointed us in a close Direction when he Described the Choke Value, and Told us a Close Frequency. We Also know that Stan did say you would have to Tune one of the Chokes to the other Chokes.

Stevie, This is where you need Funds To Purchase Ferrite Rods and put the Chokes to the test. I will do what I can, But, Some How Once choke will have to be tuned in such a way it will have to exactly agree with the adjasent choke, as no frequency will work if the one choke is not tuned into the other. This is why I think we never seen the circuit work. It makes no sense. I think this circuit does work, I think we just have not tuned into this circuit yet. I will Poke around at this Theory, and I will try and atleast get some form of Bubbles, and Then I will Brush it up in every angle to gain extra bubbles, I will tune this single circuit over a Long periode of Time now that I think I am onto this confusing stuff. I am sorry and I do opologize on my Bipolar post that is very contradicting, but these electronics Jerk me one way then another. The Truth is, There is Another Resonate Circuit that is also overunity and it has came into interference with the voltage potential does work one.
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 09, 2019, 06:36:37 am
I Updated the lawton circuit again, It has a total of 4 pots now. I will post the new schematic when I get time. Im still researching these chokes atm.
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 09, 2019, 09:59:26 am
Here is the schematic of Poch.
The coil must be bifilar.
Then tune the frequency and also the pulse width.

 
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 09, 2019, 10:22:59 am
For those that does not know,

Can you tell me what you hear him telling you?
Start at 33:26
He tries to explain the working of the cell.
I hear: two round electrodes and one is put inside of the other.
They want spark against eachother.
Thats what creates the hydrogen.
Basically he controlled a bomb.

The the same at 36:53
Lid of the cell and he saw sparks in the units (tubes)
He heard it snapping like electrical shorts
You need a strong alternator to keep the battery up.

Then at 43:46
Tiny sparks and the water started boiling

What do you hear?

Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 09, 2019, 10:37:13 am
Right now I am sorta Ticked off, Because I sent 20 thousand cycles per seconds to my setup via pwm with no success, just gets the fet hot at such high frequencys. I used a 101 cap, 0.0001

I've been using a static LED for a polarity Determinator and I cant get a potential across the cell, it goes threw it. I am having no luck with this at 20k Hertz. It promises nothing.

I will have to go back and listen to the audio, im about to run out of time for today. My Beatiful Lady lets me play electronics on some weekends and with kids if I dont stay up and not sleep I do not get to test anything. My soldering iron went out and its a Bitch soldering 2 resistors together.

I can tell you this, You guys, Please No longer use a shunt Diode. I was Blowing 10 amp shunts that got very hot. I now use a 4.7 Microfarad cap, its orange. Salvage those big ones! Also, 10 Uf, or any good size from a heating and Cooling air conditionor will work better for a shunt than a Diode, and it really recirculates the power and makes the primary coil thump, and it does not wast large amounts of heat like the shunt diode. I have made atleast 5 or so updates to the lawton circuit. Im sorry but it was flawed badly. I will update the circuit when I get time to draw. There is many errors in that circuit, Honestly, I dont see how anyone can test with such junk. I am by no way putting dave lawton down by any means, but you guys really need my schematic so you an make changes to your circuits if you are going to be using the amazing 555 timer.
Title: Hello.....anybody a reaction?
Post by: Login to see usernames on September 10, 2019, 19:45:23 pm
For those that does not know,

Can you tell me what you hear him telling you?
Start at 33:26
He tries to explain the working of the cell.
I hear: two round electrodes and one is put inside of the other.
They want spark against eachother.
Thats what creates the hydrogen.
Basically he controlled a bomb.

The the same at 36:53
Lid of the cell and he saw sparks in the units (tubes)
He heard it snapping like electrical shorts
You need a strong alternator to keep the battery up.

Then at 43:46
Tiny sparks and the water started boiling

What do you hear?

In an interview, Steven Meyer said that he would never go back to the spark cell....
Thats exactly what his father explained in Brians interview as well....
So, Stan had in his early designs and even maybe in his later ones, low voltage and high voltage in his cell.
Thats actually the same Herman Anderson said he was doing....
Its like the cold fusion setups , but then just with pulses and not with a continues dc.
So a pulse of low voltage dc with current, followed by a higher voltage spark......
Hmmmmmm
Let me think on that...



Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 12, 2019, 07:45:49 am
I CRACKED STANS TECHNOLOGY! ITS COLD ITS COLD ITS COLD!!!!!!!!!!!!!!!!!!!!!!

THE VIC IS RIGHT! ITS ALL RIGHT!

YOUR ALL LOOKING AT IT WRONG! OMG ITS SO EASY

STAN WASN'T HIDING ANYTHING, WE WERE ALL JUST TO SMART TO FIGURE IT OUT.

anyone that even knows the basics can not get this to work, IT IS NOT WHAT YOU THINK, But the schematic is correct! The Schematic is Correct!

YOU PULSE THE DIODE SO THAT NO CURRECT FLOWS THREW IT, HOW DID EVERYONE MISS THIS? I AM PRODUCING GOOD AMOUNTS IN THE MCIROWATTS REGIONS! AND WITH AN IRON CORE!

STEVIE, GO BACK AND TRY IT AGAIN BUT THIS TIME CONNECT THE DIODE THE WAY AN IDIOT WOULD AND IT WORKS!

I CONFIRMED THE CHOKES DOES INCREASE THE VOLTAGE!

THIS IS ALL YOU WILL GET FROM ME FOR ANOTHER WEEK OR SO.

HAPPY TESTING!
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 12, 2019, 07:58:57 am
Test
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 12, 2019, 13:17:12 pm
I CRACKED STANS TECHNOLOGY! ITS COLD ITS COLD ITS COLD!!!!!!!!!!!!!!!!!!!!!!

THE VIC IS RIGHT! ITS ALL RIGHT!

YOUR ALL LOOKING AT IT WRONG! OMG ITS SO EASY

STAN WASN'T HIDING ANYTHING, WE WERE ALL JUST TO SMART TO FIGURE IT OUT.

anyone that even knows the basics can not get this to work, IT IS NOT WHAT YOU THINK, But the schematic is correct! The Schematic is Correct!

YOU PULSE THE DIODE SO THAT NO CURRECT FLOWS THREW IT, HOW DID EVERYONE MISS THIS? I AM PRODUCING GOOD AMOUNTS IN THE MCIROWATTS REGIONS! AND WITH AN IRON CORE!

STEVIE, GO BACK AND TRY IT AGAIN BUT THIS TIME CONNECT THE DIODE THE WAY AN IDIOT WOULD AND IT WORKS!

I CONFIRMED THE CHOKES DOES INCREASE THE VOLTAGE!

THIS IS ALL YOU WILL GET FROM ME FOR ANOTHER WEEK OR SO.

HAPPY TESTING!


Somebody is happy here.......
uhhhhhh...what did you exactly do here?
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 12, 2019, 15:27:52 pm
hey... so you are saying the chokes have greater voltage than secondary and in opposite direction, that's why you say the diode won't conduct during pulse on?

 
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 12, 2019, 20:37:08 pm
hey... so you are saying the chokes have greater voltage than secondary and in opposite direction, that's why you say the diode won't conduct during pulse on?

YES
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 12, 2019, 20:38:33 pm
I CRACKED STANS TECHNOLOGY! ITS COLD ITS COLD ITS COLD!!!!!!!!!!!!!!!!!!!!!!

THE VIC IS RIGHT! ITS ALL RIGHT!

YOUR ALL LOOKING AT IT WRONG! OMG ITS SO EASY

STAN WASN'T HIDING ANYTHING, WE WERE ALL JUST TO SMART TO FIGURE IT OUT.

anyone that even knows the basics can not get this to work, IT IS NOT WHAT YOU THINK, But the schematic is correct! The Schematic is Correct!

YOU PULSE THE DIODE SO THAT NO CURRECT FLOWS THREW IT, HOW DID EVERYONE MISS THIS? I AM PRODUCING GOOD AMOUNTS IN THE MCIROWATTS REGIONS! AND WITH AN IRON CORE!

STEVIE, GO BACK AND TRY IT AGAIN BUT THIS TIME CONNECT THE DIODE THE WAY AN IDIOT WOULD AND IT WORKS!

I CONFIRMED THE CHOKES DOES INCREASE THE VOLTAGE!

THIS IS ALL YOU WILL GET FROM ME FOR ANOTHER WEEK OR SO.

HAPPY TESTING!


Somebody is happy here.......
uhhhhhh...what did you exactly do here?

just as the last 2 post stated... No power threw diode during pulse on, thats the way it works!
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 13, 2019, 03:04:00 am
i think we re all curious to see it. tells us more please?
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 13, 2019, 05:39:07 am
Theres nothing to tell, the on pulse isn't what matters, its when it is off the voltage flows threw the chokes and kicks back at a resonate frequency of the circuit. Thats all I know. Get your chokes and put the vic back up on the test table.

I will however say, I got resonance with several different values of capacitors, 223j, 224j, both were low freq. it is very easy to get results with these caps. anyone that builds the pwm will find it. also, I controlled the voltage at the gate of the N channel fet. I ground the gate out threw a 100k pot, and I use a 690 ohm resister on pin 3 of the timer just before the ground out pot. I use a shunt diode. its all very basic.
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 13, 2019, 19:11:49 pm
I found out the choke is actually a resonate tuning choke, you can't try to force current threw it. It is the off pulse that allows the voltage to cause a resonance. Also, I'm finding that it is very difficult to do this with 12 volt pulses. Also at very high frequencyies there is not a shunt that will hold up. Shunts was massive amounts of heat. The shunt will have to be replaced with anither coil by use of a shunt to perform more work for a maximum efficiency. I have some little success in doing just that. I am at the baby stages of the Vic, I have tapped into the proper direction but much more improvements has to be met. The circuit is that of a radio! The choke is tunable just like a radio would be. I have to add, 12 volts isn't really enough to get the voltage you need to be working with to cause a choke resonance. I'll post everything I continue to find. I don't know how Stan knew this.
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 14, 2019, 19:09:06 pm
I found out the choke is actually a resonate tuning choke, you can't try to force current threw it. It is the off pulse that allows the voltage to cause a resonance. Also, I'm finding that it is very difficult to do this with 12 volt pulses. Also at very high frequencyies there is not a shunt that will hold up. Shunts was massive amounts of heat. The shunt will have to be replaced with anither coil by use of a shunt to perform more work for a maximum efficiency. I have some little success in doing just that. I am at the baby stages of the Vic, I have tapped into the proper direction but much more improvements has to be met. The circuit is that of a radio! The choke is tunable just like a radio would be. I have to add, 12 volts isn't really enough to get the voltage you need to be working with to cause a choke resonance. I'll post everything I continue to find. I don't know how Stan knew this.

Stan was a smart cooky..... ;)
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 14, 2019, 21:05:13 pm
Yes he also did this with iron core alternator. Look in his schematic see if he uses ferrit chokes, get back to me. Thanks.
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 14, 2019, 22:01:52 pm
Just found out you have to have a scr diode, not sure what or why.
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 14, 2019, 22:53:10 pm
I am finding out you have to have a SCR, that is a Diode with a Gate Trigger to turn it off and on. Stanley had a Photo of a SCR on one of his VICs but it was not labeled.

Stevie, Go ahead and Collect you a SCR.
Unlike our time together before stevie, I will be working with you in the same manner I have in the past few weeks.

It is possible the SCR was triggered on its Highest peek.

I know I stated the Resonance on the diode off time, But I was getting results, Cold ones. BUT, I have seen other things that have also caught my eye. THE SCR IS ONE OF THEM!

Get your SCR's, and standby for further findings.

I am noticing allot more on stans patents that I did in the past. We have all been working on this a long time. I look to further stans technology than what we already have it. I look to do this with you guys as my friends and best group!
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 14, 2019, 22:55:39 pm
What we know as to date, Stans technology was based on the alternator which had a IRON core, I must look into that setup for a ferrite choke. I dont think their is one. I am Weeding out much. I have distilled water here for testing purposes. I will test as I can, Normally once a week. When I perform test, I have help, and I do not sleep on those days.

Look forward to seeing Facts threw testing not guessing.
I have recently in the last 2 days Made a Ferrite core VIC, I have tested in a few different ways. More results Later on that.
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 14, 2019, 23:03:12 pm
Sorry for Poll posting. I would like to add. My Shunt diodes are 10 amps per diode. I have fried one with over current of a primary coil of  about .9 ohms. I have had to shut the system down because twin shunts overheated. I have used a 5 UF capacitor that never got hot, but made the Primary coil THUMP and it took the place of the Shunt. I have Also used a Inductor. There is somthing here to this puzzle when debating a Shunt and Cap, or inductor.

My Next step is putting a Shunt with a Inductor. Their cant be a Resistive load greater than the FET or the current will pop the fet. At this time my thoughts are the Shunts secondary inductor must be greater in size and smaller in resistance than its primary coil. I Plan to research this further later.

I have a few of stans patents I need to print out.

Could someone Please Post the patent numbers to stans most Basic patents here for me to print off. Or direct me to the most basic ones, and where the best place is to get them as my time is limited to the point any effort you put in to help me will be greatly appreaciated.

I was told stan did not try and hide anything, and I believe that. Also, do any of you guys know where I can salvage a SCR, if not, I will have to buy one and at this Time I do not have the funds. Any donations will be greatly appreaciated. Even if it is a SCR you want to mail me. My soldering iron broke, and Im waiting on one in the mail. Im currently using an old one and its a bitch.

Message me if you need my address, to anyone that wants to mail me any cores, Scr's, or the like. I am not asking for money. If no one contributes thats ok, I understand. I will still continue to do what I can and post what I find.

I really need a 6" acrylic tube 13" long for my old tube cell. I do not even know where to purchase this. Any links for that or donations will be great! Thanks guys.

My Main focus is to Search Stans Patents for this area on the shunt. Any Info if you have any of this knowledge on hand would be greatly appreciated!
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 15, 2019, 01:16:02 am
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 15, 2019, 09:10:32 am

I really need a 6" acrylic tube 13" long for my old tube cell. I do not even know where to purchase this. Any links for that or donations will be great! Thanks guys.



Google is yr best friend.....

https://www.estreetplastics.com/Acrylic-Tube-s/45.htm
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 15, 2019, 09:12:50 am


Stevie, Go ahead and Collect you a SCR.
Unlike our time together before stevie, I will be working with you in the same manner I have in the past few weeks.



Whatever makes you feel comfortable, Brian.
I must finish my replication of Horvath.
I have invested a lot of money in that crazy setup, so at least i have to finish it.
But little babys consume a lot of my time. The little dude is worth it.. ;)
So less daddy experimenting time at the moment..
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on September 15, 2019, 18:36:12 pm
Samo Samo here!
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on October 25, 2019, 22:08:10 pm
Confirmation:

One of the famous names is Joe. Joe of the Joe Cell.
In one of his videos he said the following thing, when he was testing the power of the gas.
He said that the gas produced when the power to the cell was off is much more powerfull then the gas with the batterycharger on.
He used a 3 second pulse or pause
Steve
Title: Re: Frequency,s for pulsed electrolysis known by me, till sofar
Post by: Login to see usernames on November 01, 2019, 19:05:07 pm