in your above circuit, it looks like you are trying to get very high volts across a conductor.
The high volts stanly talks about when he talks about the vic is the volts across the upper choke, L1 i think it is. Also the fuel cell takes a small charge. Stanley measures the volts just after the diode, and just before the cap on the negative side, so you would have L1 + C wich is greater than the input voltage. and you will find that the higher the voltage in this area means less gas, i have personally seen a vic that i've created go beyond 2 thousand volts powerd from a 12 volt source, where i was probably pulsing at around 5 or 6 volts.
Stan has also said that L1 was a Amp inhibiting coil, and Also he said this choke was a Frequency Doubler. So if you can applie the dave lawton circuit to a transformer to ring the chokes and pulse the chokes, you have chokes that is resonating double the freq that the transformer is resonating at, so this means there will come a time when the back emf from the chokes are in series with the transformer, if the chokes is not double the freq of the transformers output than you will never see this LC action happen, but you will see high volts. when the LC action happens the amps after L1 and before the cap is greater than the amps Before L1, this is true because when the chokes are being charged the cell is acting as a resistor because the amps are being restricted, when the source stops restricting the amps there is a collapse and then the Cap then acts as an conductor, and capacitor.
what everyone thinks is, the water fuel cell is a conductor, but stan hit a freq, the freq of water wich allowed high volts to be shown across the fuel cell. Stan did not say that the high volts was across the fuel cell, he talked in riddles, like for example, the voltage would go to infinity if the electronics would allow it. and he says that the water fuel cell takes on a charge. this leads you to believe that he is charging the cap and the cap has high voltage across it because he tuned into the resonate frequency of water. Nothing stanley says is a lie, everything works as stan says it works, and he explaines it well, the problem is people missunderstand what stan is saying, why? for one stan says it in such a way to confuse you because he wants it to confuse you. its all part of his protection.
alot of the problem is you guy's dont have the dvd's on stan, they are very very boaring to watch, but if you have these dvd's and you sit down and you watch them, the more he talks the more he tells on his self. he is a good guy and very very clever, but if you dont know what to look for and how to determine whats going on then theres no hope. alot of the truth is in the dvd's. but i picked up my knowledge on stan over a years period hardcore testing and using stan for a hero.
if you have built this circuit im sure there is somewhere you can use it in this system for a nailgun, so its not a wast of time. i have made many circuits and thrown them away time after time. it came to a point to where i was making so many circuits i had to learn how to start etching them, thats how bad it got for me. alot of effort is put into this hobby by many people and effort is what it takes to make us see the truth.
anyways this is my point of view of the situation, im very sure water does have a resonate frequency and if you find it and amplify it im sure water will just fall apart! maybe stan found this magic freq when he used just 12 volts 40 amps to the cell from the alternator. then again, if he found resonance dont you think he would have produced more than just 7 liters a min? again, stan said voltage across his cells was 12.5 volts, and he said that the alternator restricted amps, and it does! so i guess stan hit resonance at 12 volts 40 amps. i am talking about the setup that ran stans car, the one that got it going down the road!
the alternator does indeed restrict lots of amps. stan uses pulsed dc, he also has 9 tubes. its so great how he did this! the guy is amazing!
