Author Topic: Resonance WFC measurements  (Read 36832 times)

0 Members and 9 Guests are viewing this topic.

Offline Login to see usernames

  • Sr. member
  • ***
  • Posts: 363
Re: Resonance WFC measurements
« Reply #112 on: March 21, 2012, 02:17:21 am »
waterfreak,
copper wires is also resistive wire.It has resistence too.It doesn't mean you need stainless wire.

Offline Login to see usernames

  • Jr. member
  • *
  • Posts: 35
Re: Resonance WFC measurements
« Reply #113 on: March 21, 2012, 13:43:14 pm »
Thanks for helping to keep us on track.
Perhaps Stan is just trying to throw us off by stating it is resistive wire?...

Offline Login to see usernames

  • Global Moderator
  • Hero member
  • ****
  • Posts: 3607
Re: Resonance WFC measurements
« Reply #114 on: March 24, 2012, 16:10:03 pm »
There is much to learn on tesla stuff. I found a book recently where he shows many simple inventions with a great deal of generosity. I found this book because it was cited by another inventor. I personally believe stan uses some of this to accomplish the unipolar pulsing.

good luck

Offline Login to see usernames

  • Member
  • **
  • Posts: 238
Re: Resonance WFC measurements
« Reply #115 on: March 25, 2012, 04:09:07 am »
I'm guessing your talking about the tesla colorado notes book?

Offline Login to see usernames

  • Sr. member
  • ***
  • Posts: 460
    • Global Kast : Water Fuel Cell Research
Re: Resonance WFC measurements
« Reply #116 on: March 25, 2012, 10:18:59 am »
This is a video I made 2 days ago when I was running some tests with my single cell, VIC Transformer, and VIC Circuit. My scope was connected between the diode and L1 Choke like Stephen Meyer's shows in his patent and the waveform is pretty much a perfect match as his.
http://www.youtube.com/watch?v=Wr3viEo2pVI

I have also added an attachment which is a picture of the signal across the cell.

Offline Login to see usernames

  • Global Moderator
  • Hero member
  • ****
  • Posts: 3607
Re: Resonance WFC measurements
« Reply #117 on: March 25, 2012, 18:44:48 pm »
I'm guessing your talking about the tesla colorado notes book?

"The inventions research and writing..."



Offline Login to see usernames

  • Member
  • **
  • Posts: 184
Re: Resonance WFC measurements
« Reply #118 on: March 25, 2012, 20:23:52 pm »
Seb, Tony:


I'm guessing that we've been getting this waveform from various 9ax, 8xa and similar VICs built by this and other groups for some time now.  Now where to? 

My observations show that by adjusting the resistance to ground at the negative choke and plate it appears to only reduce ringing voltages yet has no discernable effect on gas production.  For example, my ringing voltages PTP are 2000v with anything over 80k ohm and can be drawn down to 100v ptp ringing with zero resistance to ground via a 100k pot. 

kb

Offline Login to see usernames

  • Member
  • **
  • Posts: 238
Re: Resonance WFC measurements
« Reply #119 on: March 26, 2012, 04:50:48 am »
Tony, that is an interesting vid, and as you said it looks just like the waveforms shown on Steve's patent.

Is this the same setup that you have been using?   Is there any gas being produced?

From what I can see there is a high frequency ringing between each pulse....Could be a resonance between parasitic componnets of the coils or even the capacitance of the diode. I wonder how much higher the freq is than the driving freq, and if it's ringing or harmonics showing up?