Author Topic: 3500 rpm on water......  (Read 12640 times)

0 Members and 1 Guest are viewing this topic.

Online Login to see usernames

  • Administrator
  • Hero member
  • ****
  • Posts: 4462
    • water structure and science
3500 rpm on water......
« on: November 12, 2009, 14:47:41 pm »
Hi,

After rebuilding my wfc, i went for test on my 600cc 4cylinder Yamaha motorbike.
In the last test, i was able to idle this bike, but now i could even rev it up to 3500 rpm.
And that with a 1300watt powerconsumtion of my wfc.

Here a picture and a video.

Steve



« Last Edit: November 12, 2009, 19:47:18 pm by Steve »

Offline Login to see usernames

  • Sr. member
  • ***
  • Posts: 434
Re: 3500 rpm on water......
« Reply #1 on: November 12, 2009, 15:31:48 pm »
Great steve!! Nice work!!

That's a lot better than a lawnmower set-up!   ;D
And it sounds great!

Did you adjust the spark timing on your bike for this?

Webmug

Online Login to see usernames

  • Administrator
  • Hero member
  • ****
  • Posts: 4462
    • water structure and science
Re: 3500 rpm on water......
« Reply #2 on: November 12, 2009, 19:33:18 pm »
Great steve!! Nice work!!

That's a lot better than a lawnmower setup!   ;D
And it sounds great!

Did you adjust the spark timing on your bike for this?

Webmug

Thank you.
No, i didn't adjust any timing. Its all standard setup.
There is some gain in adjusting the timing, i ll guess.
Maybe laters when i am going to run my car on it.

It would have been possible to run this bike on the road, if i had big suitcases...


Steve

Offline Login to see usernames

  • 50+
  • *
  • Posts: 93
Re: 3500 rpm on water......
« Reply #3 on: November 12, 2009, 19:43:03 pm »

 Nice going, Steve.  Using gasoline in the GEET ??

Online Login to see usernames

  • Administrator
  • Hero member
  • ****
  • Posts: 4462
    • water structure and science
Re: 3500 rpm on water......
« Reply #4 on: November 12, 2009, 19:48:13 pm »

 Nice going, Steve.  Using gasoline in the GEET ??

No geet , yet, on the bike.
So, its all just 1 waterfuelcell powering the bike.

Steve

Offline Login to see usernames

  • Hero member
  • ****
  • Posts: 1019
Re: 3500 rpm on water......
« Reply #5 on: November 12, 2009, 20:22:35 pm »
just one fuel cell huh.. as in one tube or as in array? lol congrats man keep it up buddy i wanna see a 6 cylinder up in reving by next week.

Online Login to see usernames

  • Administrator
  • Hero member
  • ****
  • Posts: 4462
    • water structure and science
Re: 3500 rpm on water......
« Reply #6 on: November 12, 2009, 20:27:34 pm »
just one fuel cell huh.. as in one tube or as in array? lol congrats man keep it up buddy i wanna see a 6 cylinder up in reving by next week.


1 tube of 3 inch.....Wohaaaaa.....
Its more like a 60 plate serie drycell......... ;)

Steve

Offline Login to see usernames

  • Hero member
  • ****
  • Posts: 1019
Re: 3500 rpm on water......
« Reply #7 on: November 12, 2009, 21:02:25 pm »
my bad i didnt watch the video until after i posted the last message.. had me a dumb moment of not fully observating