Author Topic: High Voltage Circuit (VIC)  (Read 17722 times)

0 Members and 1 Guest are viewing this topic.

Offline Login to see usernames

  • Moderator
  • Sr. member
  • ***
  • Posts: 434
Re: High Voltage Circuit (VIC)
« Reply #40 on: December 29, 2009, 17:14:43 pm »
@Dynodon

Do you have progress on the HV transformer signal? Blocking negative signal with HV DIODE?
I have a few HV DIODES (20kV 10mA) but I fried my primary transformer coil.  ???

br,
webmug
« Last Edit: December 29, 2009, 18:51:04 pm by webmug »

Offline Login to see usernames

  • Sr. member
  • ***
  • Posts: 363
Re: High Voltage Circuit (VIC)
« Reply #41 on: December 29, 2009, 22:36:36 pm »
Right now I'm looking at the alternator setup.I'm still pondering the other one though.More research going on now than anything.
Don

Offline Login to see usernames

  • Hero member
  • ****
  • Posts: 980
Re: High Voltage Circuit (VIC)
« Reply #42 on: December 29, 2009, 22:52:48 pm »
Don, have you learned anything more about Stan's alternator?

Offline Login to see usernames

  • Sr. member
  • ***
  • Posts: 363
Re: High Voltage Circuit (VIC)
« Reply #43 on: December 29, 2009, 22:57:55 pm »
Not yet,I'm looking to get back down there soon.Just waiting for the owner to get some free time,and I've been short on funds do to lay off.
Don

Offline Login to see usernames

  • Jr. member
  • *
  • Posts: 47
Re: High Voltage Circuit (VIC)
« Reply #44 on: December 30, 2009, 07:53:20 am »
outlawstc, I like the vice. what about taking the knob off and replacing it with a pulley. then belt drive it to the top of the cell.
Robert

Offline Login to see usernames

  • Moderator
  • Sr. member
  • ***
  • Posts: 434
Re: High Voltage Circuit (VIC)
« Reply #45 on: December 30, 2009, 10:32:09 am »
I've got a new dangerous part to experiment with, a Flyback transformer.
As you can see in the schematic we do have a few pickup coils to choose from...guess I could use to lowest Vpp coil. In the sheet we see the type of output pulse .
Could not find a detailed data sheet, usual PHILIPS parts data sheets are difficult to find.
Don't know if this part works on 230V...must inspect the circuit board were it comes from.
It's kind of dangerous to connect it to mains.

br,
webmug 

Offline Login to see usernames

  • Hero member
  • ****
  • Posts: 980
Re: High Voltage Circuit (VIC)
« Reply #46 on: December 30, 2009, 18:17:28 pm »
I can't wait to see what that does to the water!

Offline Login to see usernames

  • Sr. member
  • ***
  • Posts: 457
Re: High Voltage Circuit (VIC)
« Reply #47 on: December 30, 2009, 20:06:17 pm »
I've got a new dangerous part to experiment with, a Flyback transformer.
As you can see in the schematic we do have a few pickup coils to choose from...guess I could use to lowest Vpp coil. In the sheet we see the type of output pulse .
Could not find a detailed data sheet, usual PHILIPS parts data sheets are difficult to find.
Don't know if this part works on 230V...must inspect the circuit board were it comes from.
It's kind of dangerous to connect it to mains.

br,
webmug
don't do it!
flybacks are normally driven by 12V-18V, if you use a square wave the voltage generated will be enormous, don't use 230V!