Ionizationx: a clean environment is a human right!
Electronics => Best WORKING circuits for WFC => Topic started by: hgul on October 12, 2014, 00:20:16 am
-
Hi everyone,
I have a problem. please help me. I download and built from www.globalkast.com , by tony woodside, Complete VIC Circuit . Everything is ok , I use 12 volt but it couldn't work. Where am I is wrong. I havent make any adjust. I added some pictures . only two leds lighting . Also I couldnt get any square wave in oscilloscop :(. is there anyone to help me ?
Thanks
-
Hi everyone,
I have a problem. please help me. I download and built from www.globalkast.com , by tony woodside, Complete VIC Circuit . Everything is ok , I use 12 volt but it couldn't work. Where am I is wrong. I havent make any adjust. I added some pictures . only two leds lighting . Also I couldnt get any square wave in oscilloscop :(. is there anyone to help me ?
Thanks
:-[ ???
-
Hi everyone,
I have a problem. please help me. I download and built from www.globalkast.com , by tony woodside, Complete VIC Circuit . Everything is ok , I use 12 volt but it couldn't work. Where am I is wrong. I havent make any adjust. I added some pictures . only two leds lighting . Also I couldnt get any square wave in oscilloscop :(. is there anyone to help me ?
Thanks
Dear Hgul,
Thanks for showing yr setup.
For years now people are trying to replicate Stans work.
But no succes yet.
Did you ask Tony for help?
Steve
-
Thanks for your answer Steve. yes I asked and mailed to Tony , and waiting for answer. :-[
-
Maybe we can help if you make a schematic of your setup.
How does yr VIC looks like?
How many turns per coil, wire thickness and winding directions, etc etc?
I seen on Tony,s documents that he had some ideas of his own, which where not the real vic setup of Meyer.
cheers
-
thanks for your help Steve. I usede Tony circuit from his website
http://www.globalkast.com/documentation.htm
http://www.globalkast.com/docs/VIC_Transformer_&_Cavity.pdf
http://www.globalkast.com/docs/VIC_Circuit_Production_Eagle-5.10.0_Files.zip
I make all of them how written in schematic . working on nearly 2,5 months :(
-
If i remember correctly, the two choke and their connections are not hooked up well.
All coils must be wind in the same direction as well.
My 2 cents is to start slowly with 2 volts on the primary, see if you can find resonance and then tune up.
Also use a 70 ohm resistor over the primary...
For now that what i know...
-
Hello Steve,
im doing many tests too here.. no results...
i think theres something on the winding of the chokes that can makes its resonant frequency lower somehow.. mine are resonating at 30khz or so.. i used insulation between each layer...
i get the step charging i guess... but no bubbles at all...
Welcome hgul keep strong.. its kind of a hard way to get it done... i think you better get the cell like meyer or steve did and start testing.. .it simply wont come out of of nothing! Believe-me... we are into this since many years.. .
if we can help you in anyway let us know.... as steve said try show the schematics of your coils..
Good luck!
-
Thanks for your answer and couraging me sebosfato :)
I read Tonys message on this forum and use his pcb from his site . also I asked him is it ok. maybe I make some mistake while structred parts of circuit.
anyway no problem. I am studying and reading about stanley meyer, :)
-
hi friends Steve and Sebosfato
Is there any users or install manual about Tony woodside pcb circuit. Do you know ?
I mean after instructed circuit like Tonys make, what must we do for perfect work circuit? is there any document about this? do you know ? Thanks so much