Ionizationx: a clean environment is a human right!
Projects by members => Projects by members => Sebosfato => Topic started by: sebosfato on September 11, 2014, 14:50:17 pm
-
This is my new cell... all hand made..
-
This is my new cell... all hand made..
i made a 1 liter reservoir in the top 10x 10x10 cm and its leaking because when i pushed the screws the resin that i used to glue it didm´t supported... i´m going to apply neutral silicone to fix that for the moment... it happens because plexiglass can bend and the resine cracks if bent... its the only flaw however in the design,,,
-
I think the neutral silicone solved! thanks mookie..
I spend much less to do this version ... than the delrin case one..
-
Well done. It looks impressive :-)
You are some steps ahead on my cells :-(
-
Well done. It looks impressive :-)
You are some steps ahead on my cells :-(
Steve was very easy to do.. almost al the holes i did on my hand machitta driller and the holes for the electrodes was made with the still driller..
i got a xy table and made out of my still driller a kind of low precision milling machine.. that worked well for plastic..
you just need the tools and the drill bits.. =) and sand paper to get the plastic back alive ... the electrical connection i made with allen screw and a screw pressed into it.
now with the foots looks like a spaceship
-
Well done. It looks impressive :-)
You are some steps ahead on my cells :-(
Steve was very easy to do.. almost al the holes i did on my hand machitta driller and the holes for the electrodes was made with the still driller..
i got a xy table and made out of my still driller a kind of low precision milling machine.. that worked well for plastic..
you just need the tools and the drill bits.. =) and sand paper to get the plastic back alive ... the electrical connection i made with allen screw and a screw pressed into it.
now with the foots looks like a spaceship
Well, if it works then it works :)
Fab, did you got the cores i send you?
-
they are still at Shipment at customs since 29 august... according to the tracking...
-
they are still at Shipment at customs since 29 august... according to the tracking...
thats odd....
Maybe they drilled the cores in seRch for dope... :)
-
Everything takes a life here...
in about a week i will get the capacitance meter and more tubes and the same wire you got... as soon as i get the cores i can make the bobbins to start coiling... hope all goes fine ???
I was wandering abou the caloric power of water and i got a not so good surprise..
fist i found that for every liter of whatever combustible you burn you are generating 1 liter of water (gasoline, diesel) plus 2000 liters of C02 carbonic gas
all that consuming 3000 liters of oxygen from the atmosphere...1/3 not returnable, because it became water that didm´t exist before! The CO2 should be returnable thru photosynthesis to reform the hydrocarbons again..
than i found that gasoline or diesel takes half of its power from its hydrogen and half from its power from the carbon content or so.
than i found that actually in terms of energy water has 2,5 less energy than gasoline comparing volume..
but the advantage is that water carry its own oxygen supply! so its the perfect fuel
The other advantage of hydrogen is that it burns completely, different from diesel of gasoline that never burns completely.
-
now i hooked up the pump on the cell and it worked great with no leaks... old and good hot glue!!!
it makes me wonder if the hydrogen cycling thru the cells is a good idea.. the water become like a solution of bubbles...
-
Well, you know that where bubbles are, no current flows.
-
In this photo the pump is operating... i don´t think a video would be of any help now this is just plain electrolysis mookie.. .
I´m using my cel phone so it takes a long time to upload videos from it... photos are just quick..
-
The core are almost arriving =)
-
now i hooked up the pump on the cell and it worked great with no leaks... old and good hot glue!!!
it makes me wonder if the hydrogen cycling thru the cells is a good idea.. the water become like a solution of bubbles...
Sebosfato, I would like to give you a heads up on your water pump. It is not a good Idea to pump water through the cells. Stan's cell was designed to be self pumped, self primed by pressure inside the cell as pressure builds up in the cell. The water well in the center of the cell leads directly to an outlet that goes out to another cavity that houses the electrostatic filter, where it is filtered and then fed back into the cell under it's own pressure from the cell. Pressure of the cell itself cause the water to leave the cell and re-enter the cell, no pump is need. (Do not use a pump.)
-
now i hooked up the pump on the cell and it worked great with no leaks... old and good hot glue!!!
it makes me wonder if the hydrogen cycling thru the cells is a good idea.. the water become like a solution of bubbles...
Sebosfato, I would like to give you a heads up on your water pump. It is not a good Idea to pump water through the cells. Stan's cell was designed to be self pumped, self primed by pressure inside the cell as pressure builds up in the cell. The water well in the center of the cell leads directly to an outlet that goes out to another cavity that houses the electrostatic filter, where it is filtered and then fed back into the cell under it's own pressure from the cell. Pressure of the cell itself cause the water to leave the cell and re-enter the cell, no pump is need. (Do not use a pump.)
Ronnie my idea with the pump was to try forcing the circulation adding the possibility to use a polymer like filter... to keep the water ever purifying...
Thanks very for the advice!
-
my cores for the vics are here!!!
i´m finishing my improvised lathe to finish the bobbins for the new cores!
i used my bench driller to create a lathe using my xy table and a iron table as support... it does well but i need to get more solid to machine the pieces with more precision...
-
This is my bobins made at home in my new mini lathe ... It works very well!
-
This is my bobins made at home in my new mini lathe ... It works very well!
well made! Can you make 4 for me, maybe?
Great cores, btw.... :)
-
Of course bro... i´m out of material because i broke some bobbins in the process... in the week i should get more material to do it! its really an adventure..
all manual!
;D
-
I´m very happy with my machine....
I´m doing some tests with the wiring of the vic with this crude bobbins but i´m bit lost...
-
I´m very happy with my machine....
I´m doing some tests with the wiring of the vic with this crude bobbins but i´m bit lost...
Just keep on turning..... ;)
-
Hey bro i tested rolling up the wire on the bobbins but they are weak and so i need new bobbin design... with thicker wall..
i think tomorrow i can get more material to get more bobbins done... i advance to you that is pretty annoying to wind this all amount of wire on..
-
ok...
Winding coils is also for me not the funniest part of this hobby...
-
Personally, I have given up on trying to wind neat tight coils by hand. I use a drill now. Faster, easier and the coils seem to work just as well.
TS
-
Personally, I have given up on trying to wind neat tight coils by hand. I use a drill now. Faster, easier and the coils seem to work just as well.
TS
So precision is not needed? Ill gues the first couple of layers must be good for the best effect.
The more you get to the outer parts it is less critical...