Author Topic: Geet project of Steve  (Read 26840 times)

0 Members and 3 Guests are viewing this topic.

Offline Hidden

  • Hero member
  • ****
  • Posts: 2122
  • Testing
Re: Geet project of Steve
« Reply #8 on: August 07, 2009, 17:42:03 pm »
Well, In my Previous post i should have included. Lines like this makes me wonder about whats really going on.

"His wife owns rights to his technology, She Turned Him in." How stupid is that? Found this on internet.

Offline Hidden

  • 50+
  • *
  • Posts: 93
Re: Geet project of Steve
« Reply #9 on: August 07, 2009, 17:57:38 pm »
I just saw an article on the 'net, yesterday, where Pantone was running an engine on "Mountain Dew", the soda, but, stated you still need a little gasoline added to the mix.

  It was a video, and I can't view them  ::)

Offline Hidden

  • Administrator
  • Hero member
  • ****
  • Posts: 3886
    • water structure and science
Re: Geet project of Steve
« Reply #10 on: August 07, 2009, 19:47:09 pm »
Well, In my Previous post i should have included. Lines like this makes me wonder about whats really going on.

"His wife owns rights to his technology, She Turned Him in." How stupid is that? Found this on internet.

If you have seen the pictures of Paul's mouth with all those infections, and nobody to help him in that jail, then YES.......a good reason for a deforce, i would say...

Offline Hidden

  • Administrator
  • Hero member
  • ****
  • Posts: 3886
    • water structure and science
Re: Geet project of Steve
« Reply #11 on: August 07, 2009, 19:55:37 pm »

Project update:

1. powergenerator dismanteld. I took the fueltank, the carb and exhaust off.
2. i got brass T-pieces of 1 inch inner.
3. I got pieces that makes 1 inch into 0.5 inch
4. i got me 2 tubes. 1 piece of 30cm Steel 1 inch widt, seamless, type EN10255
                             1 piece of 42cm steel 0.5 inch widt, seamless type EN10255

Still need the needle aka most inner rod.
Still need a compass
Still need 1 inch and 0.5 inch tool to make the thread around the tubes....Cannot find them anywhere here in Karlskrona....GAUSS??????
And of course, i need to make flansch with pipe on the intake and exhaust sides...

Steve

Offline Hidden

  • 50+
  • *
  • Posts: 96
  • "Help people enlighten to truth"
Re: Geet project of Steve
« Reply #12 on: August 07, 2009, 21:00:19 pm »
Go visit me and I can help you. :)

Offline Hidden

  • Jr. member
  • *
  • Posts: 32
Re: Geet project of Steve
« Reply #13 on: August 07, 2009, 21:27:45 pm »
Paul has said repeatedly in his recent videos that he is moving his operations/classes/promos from US to Europe, mainly near Stevie in NL.

GEETs supposed to be big in France, some of the commercial derivatives are ecopra, SPAD, etc.

Can't wait to see your results Stevie. Keep it up!

PS: The key to a successful GEET (plasma ring between rod and inner pipe) is still a secret, not yet revealed by Paul. But depends on several variables such as rod length, diameter, clearance, etc..

Offline Hidden

  • 50+
  • *
  • Posts: 93
Re: Geet project of Steve
« Reply #14 on: August 07, 2009, 22:25:04 pm »
According to the ecopra website, if you build the unit, you have to PHONE them, with all the specifics, and they will then tell you how long and the dia. of that inner rod.

  Sounds like pretty specific info is needed, to get the right ingredients, to match up. ???

Offline Hidden

  • Administrator
  • Hero member
  • ****
  • Posts: 3886
    • water structure and science
Re: Geet project of Steve
« Reply #15 on: August 07, 2009, 22:30:21 pm »
Go visit me and I can help you. :)

Hi Gauss. So you have a metalshop at yr service? Welding, cutting and thread cutters, like 1 and 0.5 inch?
We had plans to meet anyway, if all things went well here..
I have the genset here.

Steve